Paralleling Generators: Load Sharing, Droop and Protection


Paralleling is usually described as a switchgear question: add a busbar, a breaker and a controller, and two generators become one larger plant. In service the opposite is true. The busbar makes the two machines electrically and mechanically dependent, and every behaviour that was invisible on a single set becomes a shared variable: frequency, voltage, reactive power, fault current and neutral current. This page sets out how load sharing actually works, what droop does to it, and which protection functions exist only because the sets are parallel.

A parallel bus is a shared system, not a larger generator

Two 500 kVA sets on one bus do not automatically give 1000 kVA of usable capacity. They give a bus whose available capacity depends on how the load divides, how the controllers behave, how the protection is graded and what happens when one set trips. The plant rating is a number on a schedule; the operating rating must be demonstrated.

The first condition is the site ambient. A set rated at a reference ambient is not rated at 40 °C, and the derating above the reference is determined by the manufacturer’s data. The second condition is redundancy. A parallel plant with N sets and no spare capacity is less resilient than a single set with headroom, because a trip removes a share of the load and may cascade.

The third condition is the load profile. Parallel sets are often selected for a peak that lasts a short time, then operated for long periods at a small fraction of rating. The 10%-20% light-load range is a known problem for a single set; with two or three sets sharing the same small load, each machine can sit deep in that range, where combustion quality, wet stacking and maintenance intervals all suffer. The number of running sets is a control decision, not a fixed consequence of the bus design.

What changes when a second generator is connected. Each row is a design task, not an automatic benefit of paralleling.
Item Single set Parallel bus Design consequence
Capacity One rating at the site ambient Sum of the connected ratings, limited by sharing and redundancy State whether the plant rating includes a spare set or not
Frequency Set by one governor Common bus frequency; all governors interact Choose isochronous or droop control and define the master
Voltage and reactive power Set by one AVR Common bus voltage; AVRs share reactive load Set voltage droop or reactive compensation
Fault level Contribution of one machine Sum of all connected contributions Re-grade breakers, cables and protection
Neutral current Return path of one source Possible circulating current between neutral earths Choose the earthing arrangement before commissioning
Control Start, stop and load one set Start, synchronise, share, shed and stop a group Define the sequence and the failure response

kW follows the engine, kvar follows the excitation

On a parallel bus, active power is controlled by the prime mover and reactive power by the excitation system. The governor changes fuel to change torque, and torque at synchronous speed changes kW. The automatic voltage regulator changes field current to change the internal voltage, and the difference between internal voltage and bus voltage drives kvar. The two loops are not independent in practice, but treating them separately is the only way to commission them.

There are two common ways to share active power. The first is droop control: each governor has a speed-load characteristic, so as the set picks up load its speed falls slightly. If two sets have the same droop slope and the same rating, they reach the same frequency at the same percentage load and share in proportion. The second is isochronous load sharing: one controller acts as the master and sends a load demand to each set, while the governors hold frequency.

Droop is the simpler arrangement and needs no communication between sets. Isochronous load sharing holds a constant frequency and can allocate load deliberately, which matters when one set is older, smaller or being held in reserve. The trade-off is dependence on a controller and its wiring. If the load-sharing signal is lost, a well-designed system should fall back to a safe condition rather than let one set take the whole bus.

Active-power control modes. The mode determines what holds frequency and what decides the share.
Mode What holds frequency What sets the share Where it fits Main risk
Single isochronous The governor of the only running set No share to set One set on load Cannot parallel without a droop or load-sharing layer
Speed droop The bus frequency, which falls with total load The droop slope and rating of each set Simple parallel plants, base load Frequency varies with load; mismatched slopes share unequally
Isochronous load sharing A master controller and one set in isochronous mode The load demand signal to each set Plants with a mix of ratings or a reserve set Controller or signal failure
Baseload or import control The mains, when paralleled to it The import or export setpoint Peak shaving and grid-parallel operation Reverse power if the setpoint is not held

Droop is a setting, not a defect

A speed droop of a few percent is normal. It means the no-load frequency is slightly above nominal and the full-load frequency is slightly below it. The exact slope is a project setting: the manufacturer publishes an adjustable range, and the commissioning engineer chooses a value that gives stable sharing and acceptable frequency at the site. A 2% droop is a common starting point on a 50 Hz system, but the final value is determined by the manufacturer’s data and the project specification.

The important point is that droop must match. If two identical sets have different slopes, the steeper set takes less load at any common frequency. The mismatch may be small at full load and large at part load, which is exactly where parallel plants spend most of their time. The same logic applies to voltage droop and reactive sharing: an AVR with no droop can fight the other AVR, and one machine may absorb or deliver most of the reactive power.

Reactive sharing is often corrected with a reactive droop characteristic or a cross-current compensation signal between AVRs. The choice depends on the excitation system and the controller. A set with a lower excitation response may appear to carry too little kvar, while the other runs at a high field current and a high temperature. The symptom is not usually a voltage problem; it is one machine running hotter than its neighbour for no obvious reason.

Droop and compensation settings. The ranges are adjustable, and the selected values come from the manufacturer and the project specification.
Setting What it controls Effect of increasing it Symptom if mismatched
Speed droop Governor speed versus kW More frequency drop from no load to full load One set takes more kW; frequency falls further
Voltage droop AVR voltage versus kvar More voltage drop as reactive load rises Unequal kvar; one AVR runs at high field current
Reactive compensation Cross-current signal between AVRs Stronger correction of reactive imbalance Slow or oscillating kvar sharing
Governor gain Speed of response to load change Faster response, less stability margin Hunting, overshoot or a slow recovery after a load step
Load-sharing gain Trim rate of the kW demand signal Faster correction of share error Interaction between controllers, or slow correction

Synchronising: close the breaker inside a defined window

Before a set can share load it has to be connected. The incoming set must match the bus in phase sequence, voltage, frequency and phase angle, and the breaker must close at the moment the two waveforms are close enough. An automatic synchroniser adjusts the governor and AVR, then issues a close command that accounts for the breaker’s closing time. A sync-check relay supervises the same conditions and blocks a close that is outside the window.

The window is a project setting. A wide window reduces the number of failed synchronising attempts but increases the current surge and the mechanical shock at closure; a narrow window is gentler but slower to satisfy, especially on a set with a sluggish governor. The right values depend on the breaker, the set and the controller, and they should be proven during commissioning rather than copied from another site. Phase rotation must be checked before the first close, not inferred from the cable schedule.

Dead-bus closure is a separate case. When there is no live bus, the synchroniser cannot match to anything, so the first set closes onto a dead bus and establishes voltage and frequency. The sequence must prevent a second set from closing until the bus is stable, and it must define what happens if the first set fails to start. A black-start scheme is more than a battery and a starter; it is a defined order of operations with interlocks.

Sync-check parameters. Each value is a project setting influenced by the breaker and the controller; the table lists what must be defined.
Parameter What it prevents What to record at commissioning
Phase rotation Connecting two sequences that oppose each other Meter or phase-sequence test on both sides of the breaker
Voltage difference A large reactive surge at closure Bus and incoming voltage at the moment of close
Frequency slip Closing while the phase angle is moving too fast Slip setting and the observed slip before close
Phase angle Closing against a large angle difference Angle setting and the synchroniser’s close command
Breaker close time Closing late because the command was issued at the wrong angle Measured close time, not the nameplate value
Dead-bus logic A second set closing before the first is stable Sequence, timers and failure response

Protection that exists only because the sets are parallel

A single generator needs overcurrent, voltage, frequency and earth-fault protection. A parallel bus adds functions that detect power flowing in the wrong direction, a machine that has lost its excitation, and a fault that one set feeds into another. The settings come from a protection study that models the bus, the mains contribution and the cable impedances; they are not chosen from a generic table.

Reverse power is the clearest example. If a set loses its prime mover while the bus is live, the other sets can drive it as a motor. The reverse-power element detects that condition and trips the breaker. Loss-of-excitation protection detects a field failure that leaves the machine absorbing reactive power. Negative-sequence protection detects unbalanced load or an open phase, which heats the rotor. Directional overcurrent is used where a set can feed a fault through the bus in a direction the normal overcurrent element cannot distinguish.

Grading is as important as the function. A generator breaker must trip for a fault inside its own zone without tripping the whole bus, and the mains breaker must not trip for a generator-only fault. The protection study defines the time-current curves, the current transformers and the trip matrix. A relay that is set correctly in isolation can still be wrong when its curve is placed against the others.

Protection functions used on a parallel generator bus. The device numbers are identifiers; the settings come from the approved protection study.
Function What it detects Typical action Design note
Reverse power Power flowing into the generator from the bus Trip the generator breaker Needed whenever a set can be motored by the bus
Loss of excitation A field failure that makes the set absorb kvar Trip or alarm, depending on the scheme Coordinate with the AVR and the excitation limiter
Negative sequence Unbalanced current that heats the rotor Alarm or trip on a defined curve Relevant with single-phase loads and open phases
Directional overcurrent A fault fed from the generator side Trip the affected breaker Requires a defined current direction and a polarising quantity
Generator differential A fault inside the generator zone Trip both ends of the zone High-speed protection for a large machine
Voltage-restrained overcurrent Overcurrent during a voltage dip Trip on a curve that accounts for the dip Useful when fault current is limited by the generator
Sync check A close outside the synchronising window Block the close Supervises both manual and automatic close

Neutral treatment: the parallel bus creates paths that a single set does not

When two generators are connected to the same earth reference, their neutral points can become parallel paths for zero-sequence current. Circulating current can flow between the neutrals even with no load, driven by small voltage differences and third-harmonic content. The result is extra heat, nuisance earth-fault settings and a neutral current that nobody designed. The fix is an earthing arrangement, not a larger neutral cable.

A common approach is to earth the neutral at one point only for the paralleled group, or to use a neutral switching arrangement that connects the earth of the running set and isolates the others. A four-pole transfer switch can switch the neutral with the phases. A separately derived system has its own neutral-earth bond and must not be bonded again downstream. The correct arrangement depends on the source configuration and the project specification and belongs on the single-line diagram.

Neutral arrangements on a parallel bus. The choice affects earth-fault current, circulating current and transfer switching.
Arrangement Neutral earth points What it avoids What to check
Single common earth One bond for the parallel group Circulating zero-sequence current between sets Earth-fault current path and relay settings
Switched neutral per set Only the running set is bonded Unwanted parallel neutral paths Switch rating, sequence and failure mode
Four-pole transfer Neutral switched with the phases A second bond through the transfer path Neutral fault rating and transfer timing
Separately derived system One bond at the source Double bonding downstream Upstream and downstream bonding boundaries

Load steps, load shedding and the seconds before the bus is stable

Parallel operation does not remove the need to think about load steps. A large motor starting on a bus with two sets is still a step change, and the governors and AVRs have to recover without tripping. The available step depends on the set, the load and the controller settings, and it is determined by the manufacturer’s data and the project specification. A load bank can prove the response at repeatable points; the site load cannot.

Load shedding is the other half of the sequence. If one set trips, the remaining sets must either carry the load or shed the part they cannot carry. The UPS covers the seconds between mains loss and the generator carrying load, but it does not cover a generator trip that happens later. A data-centre load with a PUE of 1.4 illustrates the arithmetic: 1000 kW of IT load becomes about 1400 kW of facility load, and a 1000 kVA set at roughly 200 L/h would use about 4800 L in 24 hours if it ran continuously. Those figures are planning arithmetic from the published fuel basis, not a promise of site consumption.

Fuel and maintenance also scale with the number of running sets. A 500 kVA set at 75% uses about 80 L/h on the published basis, so two sets at that point use about 160 L/h. The annual load test at 50%-100% of rating still applies to each set, and the light-load range of 10%-20% still applies to each set. Three sets at 15% each are not one set at 45%.

Commissioning tests for a parallel plant. Each test should produce a recorded result and a clear pass or fail decision.
Test Condition What to record Pass condition
Phase rotation Both sides of every breaker Rotation result and instrument used Same sequence on all sources
No-load synchronising Incoming set matched to the bus Voltage, slip, angle and close time Close inside the approved window
Load sharing at 25%, 50%, 75% Two or more sets on a stable load kW and kvar per set, bus frequency Share within the project tolerance
Load step A defined block load applied and removed Frequency and voltage dip, recovery time No trip; recovery inside the project limit
Reverse power One set motored or its prime mover disabled Trip value and time Correct breaker trips without tripping the bus
Loss of one set The largest set trips on load Remaining load, frequency, load shed The bus remains stable and within rating
Neutral current Balanced and unbalanced load Neutral current per set and at the bond No unexplained circulating current

Send the single-line diagram, the load profile and the settings

A parallel review starts with three documents: the single-line diagram showing every source, breaker and neutral bond; the load profile with the largest step and the longest low-load period; and the proposed governor and AVR settings. With those, the load-sharing mode, synchronising window, protection grading and earthing arrangement can be checked as one system. Without them, the review can only repeat the datasheet.

Can I parallel two generators of different sizes?

Yes, if the governors and AVRs are set so the share is proportional to rating and the protection is graded for both machines. Either droop with matched slopes or isochronous load sharing can allocate the share. The limiting cases are the smallest set’s step response, the largest set’s minimum stable load and the fault contribution of the combination. The final arrangement is determined by the manufacturer’s data and the project specification.

What speed droop should I set?

Start with the manufacturer’s adjustable range and the value used for the governor’s stability setting, then prove it at 25%, 50% and 75% load. A few percent is common, but the correct value depends on the plant, the load steps and the required frequency band. Two identical sets should end up with the same slope; a set with a different rating needs a slope that produces the intended share. Record the as-left setting at commissioning.

Why does one generator take more reactive power?

Because the AVRs are not sharing the same voltage-error characteristic. One AVR may have a slightly higher voltage setpoint, a different droop setting or a different response. The result is a circulating reactive current that does not show up as kW but does show up as field current and temperature. Reactive droop or cross-current compensation is the usual correction; the settings come from the excitation system supplier and the commissioning tests.

What is reverse power protection for?

It detects a generator that is taking power from the bus instead of delivering it. That happens when the prime mover loses fuel, a breaker opens, or a drive coupling fails. Without the protection, the other sets motor the failed machine, which can damage it. The element should trip the generator breaker and should be coordinated with the load-shedding sequence so the bus remains stable.

Can parallel generators share one neutral earth?

They can, but the neutral path has to be designed as one system. Multiple neutral-earth bonds can create circulating zero-sequence current between the sets, and the earth-fault current can split in ways the relay settings do not expect. A single common bond, a switched neutral or a separately derived arrangement are the usual choices. The correct one depends on the transfer switching and the source configuration.

How do I test load sharing?

Use a load bank or a controllable site load and hold steady points at 25%, 50% and 75% of plant rating. At each point record kW, kvar, frequency, voltage and the share error between sets, then apply a defined load step and record the dip and recovery. Repeat with the largest set out of service to prove the remaining plant and the load-shedding sequence. The acceptance tolerances are project values, not generic figures.

Send the single-line diagram, the load profile and the proposed governor and AVR settings. The reply sets out the load-sharing mode, synchronising window, protection grading and neutral arrangement, in writing.

Request a quote WhatsApp the sales desk

Written and maintained by the KVA Grid sales engineering desk. The planning figures on this page are published elsewhere on this site: the fuel basis of 0.24-0.29 litres per delivered kWh and the 500 kVA figures of 101, 80 and 60 litres an hour at full, 75% and 50% load from fuel consumption; the annual load test at 50% to 100% and the 10% to 20% light-load range from maintenance scheduling; the 40 °C reference ambient from hot and humid climates; the UPS bridging the seconds to generator pickup, the PUE 1.4 example and the 1000 kVA case at roughly 200 litres an hour and about 4800 litres in 24 hours from data center backup power; parallel operation and reverse-power protection from peak shaving control and switchgear; negative-sequence and harmonic effects from harmonic mitigation; repeatable load points from load bank testing; the handover record from standby generator commissioning; site ambient and room conditions from generator room ventilation; fuel condition from fuel polishing; and transfer and ride-through from generator and UPS interaction. Droop values, synchronising windows, protection settings, load-sharing tolerances and neutral arrangements are determined by the equipment manufacturer’s data and the project specification. Nothing on this page is a quotation for a particular project. Reviewed 4 November 2026.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top
WhatsApp