A UPS is quoted in kVA, but a generator does not see kVA. It sees a rectifier that draws current in pulses, a power factor that is close to unity only after filtering, and a DC bus that walks in after the transfer. Size the set on the UPS nameplate and the site ends up with a generator that trips on the load it was bought to carry. This page sets out what the rectifier does to the alternator, how much margin each front end needs, and how to test the pair.
The short answer: the generator sees a different load
A double-conversion UPS takes the mains, rectifies it to DC, and rebuilds a clean sine wave for the load. The load side is well behaved. The input side is not: the rectifier draws current in short pulses around the peak of the voltage wave, and those pulses contain harmonics that a generator’s alternator has to supply. The current the UPS reports as its input is an rms figure; the current the alternator actually heats up on is not the same shape.
Three numbers decide whether the pair works: the UPS input current distortion, the generator’s subtransient reactance, and the size of the largest step the UPS presents when it transfers or recharges. The first two set the voltage distortion at the generator terminals. The third sets whether the engine and the AVR can hold the bus while the rectifier walks in. A set chosen on the UPS kVA alone answers none of them.
| Load | Current waveform | What it stresses |
|---|---|---|
| Resistive, such as heaters and lighting | Sinusoidal, in phase with the voltage | kW, cooling and fuel; the alternator is lightly stressed |
| Motor | Sinusoidal at running load, with a large inrush at start | Voltage dip at start, then kW and kvar at running load |
| Rectifier, such as a UPS or a drive | Pulsed, rich in 5th, 7th and higher harmonics | Alternator heating, voltage distortion, neutral current and AVR stability |
Why a UPS is not a resistive load
The rectifier in a double-conversion UPS conducts only when the input voltage exceeds the DC bus voltage, so the current arrives in narrow pulses rather than as a smooth sine. Without an input filter or a DC bus choke, a six-pulse rectifier commonly draws a current with a total harmonic distortion of 25 % to 35 %. Add the input filter and the figure falls to roughly 5 % to 10 %; a twelve-pulse rectifier lands around 10 % to 15 %; an active front end can hold it below 5 %.
The input power factor of a modern filtered UPS is close to unity, often 0.95 to 0.99, which is why the UPS looks like a well-behaved load on a utility supply. On a generator the same load is harder, because the source has a much higher impedance than the grid. The harmonic currents meet that impedance and produce a voltage waveform with flat tops and notches, and the alternator has to carry harmonic current it was not sized for.
The neutral is part of the same problem. Triplen harmonics add in the neutral rather than cancelling, and a supply that was designed for balanced linear loads can see more current in the neutral than in a phase. That is why the neutral on a generator supply is specified as a full phase conductor rather than a reduced one.
What the alternator does with a rectifier load
An alternator is a source with a subtransient reactance, typically around 0.10 to 0.20 per unit for the machines used on generator sets. When a pulsed current flows, the voltage drop across that reactance is pulsed too, and the result is a distorted terminal voltage. The higher the reactance and the larger the harmonic current, the deeper the notches and the flatter the peaks.
The AVR tries to correct the rms voltage, and it can only correct what it can measure and what its response time allows. A fast AVR on a low-reactance alternator produces a cleaner waveform than a slow AVR on a high-reactance machine of the same kVA. This is why two 1000 kVA sets can behave very differently on the same UPS, and why the UPS maker’s generator requirement is written against the alternator’s characteristics rather than against kVA alone.
There is a thermal limit as well. Harmonic currents do not produce useful torque; they produce additional losses in the stator and the rotor. An alternator run at its rated kVA with a heavily distorted current runs hotter than the same alternator on a linear load, and the standard derating factors used by alternator makers exist to account for it. A set that is only just large enough on kVA can be thermally inadequate on a rectifier load.
Sizing: the multiplier that matters
The planning multipliers below are the ones used to start a quotation, not a substitute for the UPS maker’s stated generator requirement. They assume a 400/230 V, 50 Hz set with a conventional alternator, and they are applied to the UPS input kVA, not to the UPS output kVA.
Two corrections sit on top of the multiplier. First, the battery recharge load: after an outage the charger adds roughly 10 % to 20 % of the UPS rating for the recharge period, and the generator has to carry the critical load and the charger at the same time. Second, the ambient: a set rated at 40 °C loses capacity at the 45 °C to 50 °C ambients common in the Gulf, and the derating applies to the figure that comes out of the multiplier.
| UPS input stage | Typical input current distortion | Planning multiplier on UPS input kVA | What drives the number |
|---|---|---|---|
| Six-pulse, no filter or DC choke | 25 % to 35 % | 1.5 to 2.0 | Harmonic heating and voltage notching; the worst case for a generator |
| Six-pulse with input filter or DC choke | 5 % to 10 % | 1.25 to 1.5 | Much lower distortion, but the filter can present a leading power factor at light load |
| Twelve-pulse | 10 % to 15 % | 1.2 to 1.35 | Lower harmonic content, at the cost of a phase-shifting transformer |
| Active front end | Below 5 % | 1.1 to 1.25 | Near-sinusoidal input current; the remaining margin is for step load and recharge |
The multiplier is not the only check. A set that is large enough for the steady state can still fail the step: if the UPS presents its full rectifier load in one block, the voltage and frequency dip may exceed what the UPS will accept, and the UPS transfers to battery or drops the load. The cure is a rectifier walk-in, a staged load or a larger set, and which one is right depends on the UPS and on the site sequence.
Voltage and frequency through the transfer
A double-conversion UPS is tolerant of a wide input window, often 40 to 70 Hz and a voltage band well beyond the nominal, which is why it rides through the period while the generator starts and stabilises. That tolerance is what makes the pair work, and it is also why a marginal generator can go unnoticed for years: the UPS accepts the waveform, the batteries top up the difference, and nobody measures the distortion at the generator terminals.
What matters during the transfer is the shape of the step, not only the steady-state figures. The set starts, reaches rated speed, the changeover closes, and the rectifier begins to draw. If the rectifier has no walk-in, that first block can pull the voltage down far enough to trip the UPS to battery, which restarts the cycle. A rectifier that ramps over five to thirty seconds gives the engine and the AVR time to respond, and it is a setting worth confirming at commissioning rather than discovering during an outage.
Frequency is the second half of the same problem. The engine’s governor responds to load with a droop and a recovery time, and the UPS input window has to cover the dip without transferring. On a set with a mechanical governor the dip can be larger and slower than on an electronic one, and a UPS set to a narrow window will transfer to battery on a step that the generator actually survived.
| Stage | What the UPS input sees | What decides the outcome |
|---|---|---|
| Mains fails, UPS on battery | No input; the load is on the inverter | Battery autonomy against the generator’s start and stabilise time |
| Generator reaches speed, changeover closes | A voltage and frequency that may still be moving | The UPS input window, and the changeover’s transfer time |
| Rectifier starts to draw | A step of pulsed current, with harmonics | Walk-in setting, alternator reactance, AVR response, engine governor |
| Battery recharge begins | An additional load of roughly 10 % to 20 % of the UPS rating | Charger setting and the set’s margin above the critical load |
| Mains returns, retransfer | A change of source, with a possible phase difference | The changeover type; a closed transition needs a designed parallel operation |
Topologies: double conversion, line interactive and rotary
A double-conversion UPS is the hardest load for a generator because its rectifier runs continuously and its input current is pulsed. A line-interactive UPS draws sinusoidal current in normal operation and only runs its inverter on battery, so the generator sees a much more ordinary load; the trade is that the load is exposed to the mains waveform while the mains is present. A rotary UPS uses a motor-generator set, which presents a motor load to the generator and isolates the critical load from the harmonics entirely, at a higher capital cost and with its own maintenance.
Modular UPS systems add a detail: the number of rectifier modules online changes with load, so the harmonic spectrum and the step size change with the site’s load profile. A test at full load does not prove the behaviour at 20 % load, and a test at 20 % does not prove the full-load case. Both belong in the commissioning plan.
ECO mode is the setting that most often surprises a generator design. In ECO mode the load runs on bypass, so the generator sees the IT load directly rather than through the rectifier, and the transfer back to inverter on a disturbance is a step the set has to absorb. A site that intends to run ECO mode should say so in the enquiry, because the generator sizing case changes.
Harmonic mitigation and what it does to the set
There are four common ways to reduce the harmonic current a UPS presents, and each one changes the generator sizing case rather than simply removing a problem. A passive input filter reduces the current distortion but can present a leading power factor at light load, which an AVR may not like. A twelve-pulse rectifier uses a phase-shifting transformer to cancel the lowest harmonics, and it is effective but heavy. An active front end shapes the input current to near-sinusoidal and is the cleanest load for a generator. An active harmonic filter compensates downstream, and it has to be rated for the current it injects.
| Option | Effect at the generator terminals | Trade-off |
|---|---|---|
| Passive input filter | Lower current distortion, lower voltage notching | Leading power factor at light load; the AVR has to stay stable |
| DC bus choke | Higher conduction angle, lower harmonic content | Some efficiency loss and heat inside the UPS |
| Twelve-pulse rectifier | Lower 5th and 7th harmonic current | Phase-shifting transformer: weight, footprint and cost |
| Active front end | Near-sinusoidal input current, unity power factor | Higher UPS cost; its own high-frequency switching has to be filtered |
| Active harmonic filter | Compensates the harmonic current at the point of connection | Rated for the injected current; another device to maintain |
Testing the pair, not the parts
A load bank test proves the generator. A UPS self-test proves the UPS. Neither proves the pair, and the failure that matters happens between them. The test that does prove it runs the site sequence with the load bank as the critical load: mains off, UPS on battery, generator start, changeover, rectifier walk-in, recharge, retransfer, and a measurement of the voltage distortion at the generator terminals at each stage.
What is recorded: the voltage and frequency at the generator terminals before, during and after the rectifier step; the current distortion at the UPS input; the time the UPS spent on battery; the recharge current; and any transfer of the UPS back to battery after the generator was already carrying. That last one is the number that exposes a marginal set, because it happens silently in normal operation and only becomes visible when the battery is already depleted.
| Test | What it proves | What it misses on its own |
|---|---|---|
| Generator load bank test | The set carries its rating and rejects the heat | The rectifier load, the transfer and the UPS behaviour |
| UPS self-test and battery test | The inverter and the battery autonomy | Whether the generator can accept the rectifier and recharge |
| Transfer test with the bank | The sequence from mains loss to generator carrying load | The building’s real load profile and the UPS ride-through under it |
| Integrated systems test | The whole chain, including cooling and the site’s own controls | Nothing, if the load profile is representative; it is the most expensive to arrange |
What we specify for a UPS-backed site
The enquiry needs five facts before a set can be sized: the UPS output kVA and power factor, the rectifier type and its input current distortion, the battery recharge current, the largest step the UPS can present, and the site ambient. With those, the multiplier, the derating and the step check can be worked through and the result is a rating rather than a guess.
On the generator side, the specification should state the alternator’s subtransient reactance, the AVR response, the governor type and the set’s rating at the site ambient rather than at 40 °C. On the UPS side, it should state the walk-in setting, the input window and whether ECO mode will be used. Those are the settings that decide whether the pair works, and they are all fixed before the equipment arrives.
The mistakes that cost the most
| Mistake | What it costs | What prevents it |
|---|---|---|
| Sizing the set on UPS output kVA | The rectifier, the recharge and the losses are all outside the number | Size on UPS input kVA, then apply the rectifier multiplier and the ambient derating |
| Ignoring the recharge load | The set is adequate for the critical load and overloaded for the hour after an outage | Add 10 % to 20 % of the UPS rating for the recharge period |
| No walk-in on the rectifier | The first block of load trips the UPS back to battery, and the cycle repeats | Set a ramp at commissioning and prove it in the transfer test |
| Comparing a 40 °C rating with a 48 °C site | The set is derated on the day it is needed, and the shortfall appears as a trip | Use the ambient-corrected rating in the sizing calculation |
| Testing the generator and the UPS separately | Both pass, and the pair fails on the first real outage | Run the sequence with a load bank and record the distortion at the terminals |
| Assuming ECO mode behaves like double conversion | The generator sees a different load and a step on transfer that was never tested | Declare ECO mode in the enquiry and test the transfer it implies |
Questions about generators and UPS loads
Do I really need 1.5 to 2 times the UPS rating in generator kVA?
That range applies to an unfiltered six-pulse rectifier, which is the hardest common load. A filtered six-pulse unit commonly needs 1.25 to 1.5 times, a twelve-pulse unit 1.2 to 1.35, and an active front end 1.1 to 1.25. The UPS maker’s generator requirement is the figure to design to, because it already accounts for the rectifier and the walk-in; the multipliers here are for a first-pass quotation and for checking a figure that looks too small.
Why does the UPS go back to battery after the generator has started?
Because the generator’s voltage or frequency left the UPS input window during the rectifier step, or because the waveform was distorted enough that the UPS treated it as a bad supply. The usual causes are a rectifier with no walk-in, a set that is too small for the step, a governor that is slow to recover, or an input window set too narrow. The transfer test shows which one it is, and the fix is a setting or a sizing change rather than a repair.
Does a modern UPS with a low input THD still need a large generator?
It needs less margin than an unfiltered rectifier, but it still needs more than a resistive load of the same kW. An active front end draws a near-sinusoidal current, so the harmonic heating largely goes away; what remains is the step at transfer, the recharge load and the ambient derating. That is why the multiplier falls to about 1.1 to 1.25 rather than to 1.0.
Is a line-interactive UPS easier on a generator?
Yes, in normal operation. It passes the mains through and draws a sinusoidal current, so the generator sees the IT load rather than a rectifier. The trade is that the critical load is exposed to the mains waveform and to the transfer, and the inverter has to pick up the load on battery. Which topology is right depends on how much ride-through and conditioning the load needs, not only on the generator.
Can a harmonic filter make the generator problem worse?
It can change it. A passive filter reduces the harmonic current but can present a leading power factor at light load, and an AVR on a lightly loaded set may become unstable with a leading load. An active filter compensates the current but has to be rated for what it injects. Either is a design decision that belongs in the same calculation as the generator rating, not an add-on after the set is chosen.
What is the one test that proves the installation?
The transfer test with the load bank connected as the critical load, measuring the voltage at the generator terminals and the current at the UPS input through the whole sequence. It shows the start, the changeover, the rectifier step, the recharge and the retransfer in one record, and it is the only test that reproduces the failure mode this page is about. The load bank test alone proves the machine, and the UPS self-test alone proves the UPS.
Send the UPS datasheet with the load list
Tell us the UPS output kVA and power factor, the rectifier type, the recharge current and the site ambient. The reply carries the generator rating, the alternator characteristics and the settings that have to be proved at commissioning, in writing.
Written and maintained by the KVA Grid sales engineering desk. The planning figures on this page are the ones published elsewhere on this site: the UPS as the short bridge between mains loss and the generator carrying load, the site load rather than the IT load as the sizing basis, and the 1000 kVA example at 0.8 power factor, roughly 200 litres an hour and about 4800 litres for 24 hours, from data center backup power; the relation between subtransient reactance and voltage dip from starting current and motor starting; the harmonic current in the neutral and the full-size neutral from voltage and phases; and the 40 °C reference with derating above it from hot and humid climates. The rectifier distortion ranges and the sizing multipliers are planning values: the UPS maker’s generator requirement, the alternator data and the project specification govern the equipment that is built. Nothing on this page is a quotation for a particular project. Reviewed 2 November 2026.
