Diesel generator fuel consumption per hour: how to calculate it

Fuel consumption follows the running kW, not the kVA rating. Multiply the electrical load by the engine’s specific consumption — about 190 to 230 g/kWh depending on set size — and divide by the density of diesel, 0.84 kg/L. A 500 kVA set at full load (400 kW) burns about 101 L/h, and about 60 L/h at half load. The working figure is 0.25 to 0.30 L of diesel for every kWh delivered.

The formula, and the two numbers it needs

Two figures decide the answer: the load in kW, and the specific fuel consumption of the engine in g/kWh. Everything else is arithmetic.

L/h = kW × 1.06 × g/kWh ÷ (1000 × 0.84)  ·  L per delivered kWh = g/kWh × 1.06 ÷ 840

The 0.84 is the density of diesel in kg/L at 15 °C, which is what turns a mass of fuel into a volume you can buy. The 1.06 is the loss between the shaft and the terminal box: the alternator and the cooling system take roughly 4 to 6 %, so the engine has to produce about 6 % more power than the set delivers. If your figure already comes from a datasheet L/h curve, that curve is normally drawn against electrical load and the 1.06 is already inside it.

Worked once, on a 400 kW load with an engine quoted at 200 g/kWh at the shaft: 400 × 1.06 = 424 kW at the shaft, and 424 × 200 ÷ 840 = 101 L/h. The same set read straight off a datasheet fuel curve gives the same number, because the curve is drawn against the 400 kW electrical load. Both routes are the same machine.

One energy check that keeps the figure honest: a litre of diesel carries about 35.9 MJ, or 9.97 kWh of heat. At 0.253 L per delivered kWh the set is turning roughly 40 % of that heat into electricity, which is where a diesel set at full load should sit. Any calculation that comes out at 0.15 L/kWh is claiming a 60 % efficient diesel engine, and there is no such machine.

Fuel consumption per hour by set size

Full-load figures for standard set sizes at 0.8 power factor, 50 Hz, 400 V, from a 20 kVA machine up to 2,000 kVA. The 100 % column is the prime rating running fully loaded; the 75 % and 50 % columns are what most sites actually run at for most of the year.

Typical fuel consumption of a diesel generator set, in litres per hour, at three load points. Part-load figures assume the load is a steady kW demand, not a motor starting.
Set rating Prime output 100 % load 75 % load 50 % load L per kWh at 100 %
20 kVA 16 kW 4.6 L/h 3.7 L/h 2.7 L/h 0.29
50 kVA 40 kW 11.4 L/h 9.1 L/h 6.7 L/h 0.28
100 kVA 80 kW 22 L/h 17.5 L/h 13 L/h 0.28
200 kVA 160 kW 43 L/h 34 L/h 25 L/h 0.27
250 kVA 200 kW 53 L/h 42 L/h 31 L/h 0.26
300 kVA 240 kW 63 L/h 50 L/h 37 L/h 0.26
400 kVA 320 kW 82 L/h 65 L/h 48 L/h 0.26
500 kVA 400 kW 101 L/h 80 L/h 60 L/h 0.25
800 kVA 640 kW 158 L/h 126 L/h 93 L/h 0.25
1000 kVA 800 kW 194 L/h 155 L/h 115 L/h 0.24
2000 kVA 1600 kW 376 L/h 299 L/h 222 L/h 0.24

Read the table with one rule: the litres per hour are proportional to the kW you are actually drawing, and the litres per kWh are not. A 500 kVA set burns 40 % less fuel per hour at half load than at full load, but each of those kWh costs about 18 % more in fuel than the kWh it delivered at full load.

Part load: cheaper per hour, dearer per kWh

The same machine, four load points, one number that does not move the way people expect. The litres per hour fall as the load falls; the fuel cost of each kWh rises, because a diesel engine loses efficiency faster than it loses load.

The same 500 kVA / 400 kW set at four load points, on the same fuel. The last column is the fuel cost of a kWh against the cost at full load.
Load Electrical output Fuel L per kWh Fuel per kWh vs full load
100 % 400 kW 101 L/h 0.253 Baseline
75 % 300 kW 80 L/h 0.268 +6 %
50 % 200 kW 60 L/h 0.298 +18 %
25 % 100 kW 37 L/h 0.366 +45 %

Two practical consequences. The first is money: a set that spends its life at 30 % load can burn 30 to 40 % more fuel per kWh than the same set at 75 % load, which over 2,000 running hours a year is a large number. The second is mechanical: a diesel engine held below roughly 30 to 40 % load for long periods runs cool, the combustion chamber never reaches its working temperature, and unburnt fuel and oil coke build up on the pistons and in the exhaust — the condition usually called wet stacking, and the reason a generator can need an early overhaul even though it has never been overloaded.

That is why a sizing calculation aims at a running load between 70 % and 85 % of the prime rating, and why the biggest set that fits the budget is usually the wrong answer for fuel and for engine life.

Specific consumption by size class

Small engines are less efficient than large ones, and that shows up in the fuel figures. The table below gives the engine-side specific consumption behind the L/h numbers above, and the resulting cost per delivered kWh. The full-load figure improves as the set gets bigger; the part-load penalty applies to all of them.

Typical engine specific fuel consumption at full load, by set size, and the resulting litres per delivered kWh. Values are for 50 Hz sets at 0.8 power factor.
Set size Engine specific consumption L per delivered kWh Where it fits
20 to 50 kVA 225 to 230 g/kWh 0.28 to 0.29 Workshops, telecom sites, small retail
100 to 200 kVA 212 to 218 g/kWh 0.27 to 0.28 Clinics, guesthouses, light industry
250 to 400 kVA 203 to 207 g/kWh 0.26 Hotels, supermarkets, mid-size plants
500 to 800 kVA 196 to 200 g/kWh 0.25 Hospitals, production lines, data halls
1000 to 2000 kVA 186 to 193 g/kWh 0.24 Large plants, district cooling, parallel sets

This is the reason a 100 kVA set cannot be compared with a 500 kVA set on litres per hour alone. Per hour it is obvious which one burns less; per kWh the gap is only about 15 %, and per kWh of useful energy the small set drawn at 30 % load is the worst of the group.

Fuel for an outage, a test, and a month

Once the litres per hour are known, the rest is multiplication. Four examples at common loads, for the outage lengths a standby site actually sees:

Fuel needed for typical outage lengths. Loads are steady kW demands at the stated percentage of the prime rating.
Set Running load Fuel 4 hours 8 hours 12 hours
100 kVA 40 kW (50 %) 13 L/h 52 L 104 L 156 L
500 kVA 240 kW (60 %) 68 L/h 272 L 544 L 816 L
500 kVA 400 kW (100 %) 101 L/h 404 L 808 L 1,212 L
1000 kVA 600 kW (75 %) 155 L/h 620 L 1,240 L 1,860 L

Add the monthly test runs, which are easy to forget: a 30-minute weekly test at 60 % load on the 500 kVA set is about 34 L a week, which is roughly 150 L a month and 1,800 L a year — more than a full tank, from tests alone.

When that number turns into a tank, two corrections matter. A tank is not usable to its nominal volume: the fuel pick-up sits 50 to 100 mm above the bottom of the tank, so allow 5 to 10 % of the volume as unusable, and a further margin for the fact that a tank is rarely filled to the brim. A 1,000 L tank therefore gives about 850 to 900 L of running fuel, which is about 13 hours on the 500 kVA set at 60 % load, not the 15 hours a simple division suggests.

What else moves the number

  • Load factor, above everything else. Fuel per hour tracks the kW almost linearly; fuel per kWh does not, as the part-load table above shows. Get the load list right before buying anything — the method is in how to size a diesel generator.
  • Which rating the set is run at. A standby set and a prime set of the same kVA carry different ratings and different fuel curves. Running a machine on continuous duty against its standby figure understates both the load and the fuel; the difference between the two ratings is set out in prime vs standby power.
  • Ambient temperature and altitude. The ISO 3046 reference is 25 °C at sea level. Above that the engine loses roughly 1 to 2 % of its rated power per 5 °C, so a set corrected for a 45 °C Gulf summer must work harder for the same kW and burns a little more per delivered kWh. Altitude has the same effect on naturally aspirated engines.
  • Fuel temperature and density. The 0.84 kg/L in the formula is at 15 °C. Diesel expands by roughly 0.1 % per °C, so fuel delivered at 45 °C into an external tank is around 3 % less dense than the reference figure, and litres bought do not match litres burned exactly.
  • Maintenance state. A blocked air filter, worn injectors or a fouled turbo raise consumption by several per cent before anything is visibly wrong. Fuel figures are quoted for a set in service condition.
  • The load’s own profile. Motors, chillers and rectifiers draw the kW at a power factor below 1, and a set rated in kVA carries a current that the kW figure alone does not show. The link between the two units is covered in kVA vs kW.

Checking the figure on site

Two methods, both worth running once, because a datasheet curve and a real installation rarely agree to better than 5 %.

  • The refill method. Record the tank level, run the set at a steady known load for one hour, then refill from a measuring can and record the litres. This gives you litres per hour at that load, directly, and it also confirms the fuel gauge and the dipstick. A 500 kVA set held at 240 kW should take about 68 L in the hour.
  • The meter method. Read the kWh meter on the generator output at the start and end of a month, and divide the litres purchased in the same month by the kWh delivered. That ratio is the real cost of a kWh on this site, and it captures everything the datasheet cannot: the actual load factor, the ambient, and the maintenance state. It is also the number to compare between two sets.

Where a load bank is available, use it to hold the load steady at 50 %, 75 % and 100 % and build the site’s own curve. Without one, the load meter and the kWh meter together give the same answer over a longer period.

Mistakes that cost money

  • Calculating from kVA. A 500 kVA set is a 400 kW set at the reference power factor. Treating 500 as the running load overstates the fuel by 25 %, and the error then propagates into the tank size and the fuel budget.
  • Using the flat 0.2 L/kWh rule. That figure is 168 g/kWh. It is reachable by a large set at full load and by nothing else: a 100 kVA set at half load sits near 0.33 L/kWh, and a 500 kVA set at a quarter load near 0.37 L/kWh. Budget on 0.25 to 0.30 unless the set is a large one that will run fully loaded.
  • Applying the g/kWh figure to the delivered kWh without the loss factor. Engine curves are quoted at the shaft. Skipping the 1.06 understates fuel by about 6 %, which is small per hour and not small over a year.
  • Assuming fuel is linear in load. Litres per hour are close to linear; litres per kWh are not. Two sites with the same annual kWh can differ by more than a third in fuel if one runs at 75 % and the other at 25 %.
  • Planning the tank on nominal litres. Usable volume is 85 to 95 % of the nameplate after the pick-up height and the working margin are taken out. Size the autonomy on usable litres, then add the sizing margin on top.
  • Ignoring the test runs. Weekly no-load or light-load tests are real hours and real litres. A 500 kVA set tested 30 minutes a week at 60 % load adds about 1,800 L a year, which is a tank of fuel nobody budgeted for.

Questions

How much fuel does a 500 kVA generator use per hour?

About 101 L/h at full load, which is 400 kW at 0.8 power factor. At 75 % load it is about 80 L/h, and at half load about 60 L/h. The figures for the 500 kVA range are quoted against their own datasheets; the ratio between the three load points is what matters for a fuel budget.

How do I calculate fuel consumption from g/kWh?

Multiply the electrical load in kW by 1.06, multiply by the specific consumption in g/kWh, and divide by 840. The 1.06 is the alternator and cooling loss; the 840 is the density of diesel, 0.84 kg/L, expressed in g/L. A 400 kW load on an engine quoted at 200 g/kWh gives 400 × 1.06 × 200 ÷ 840 = 101 L/h.

Does a generator use less fuel at part load?

Less per hour, yes; less per kWh, no. On a 500 kVA set the hourly figure falls from 101 L/h at full load to 60 L/h at half load, but the fuel per kWh rises from 0.253 to 0.298, about 18 % more expensive per unit of electricity. Below 30 % load the engine also runs too cool, and wet stacking becomes a maintenance risk.

How much fuel per kWh should I budget for?

0.25 to 0.30 L per delivered kWh for a set running between half load and full load. Use 0.30 if the load is expected to sit under 50 % for much of the year, and 0.25 for a large set that will run near full load. The number is a budgeting figure, not a datasheet value — every set is quoted against its own fuel curve.

How long will a 1,000 litre tank last?

Take 850 to 900 L as usable. On a 500 kVA set at 60 % load, about 68 L/h, that is roughly 13 hours; at full load, about 8.5 hours. For a plant that has to ride through a full working day, the 1000 kVA range and its larger tank options are the usual next step rather than a second day tank.

What to send for a fuel and tank calculation

Send the load list with the running kW of each group, the expected hours per outage and per year, the site ambient temperature, the tank volume you can provide, and the supply voltage and frequency. The running kW sets the litres per hour, the hours set the litres per event, and the tank volume decides how much has to be topped up between events. How the tank itself is chosen — base, bulk or day tank, the usable volume behind the nominal figure, and the routine that keeps stored diesel usable — is set out in generator fuel tank, autonomy and fuel management.

Get the fuel figures for a specific set

We answer with the litres per hour at 50 %, 75 % and 100 % load, the tank volume and the autonomy for your site — in writing, usually the same working day. The full range is on the diesel generator range page.

Request a quote WhatsApp the sales desk

Written and maintained by the KVA Grid sales engineering desk. Fuel figures are typical values for 50 Hz, 400/230 V, three-phase sets at 0.8 power factor, not a datasheet: every set is quoted against its own fuel curve, and consumption follows the load, the ambient and the maintenance state. Reviewed 30 September 2026.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top
WhatsApp