A generator room is not a box that keeps the rain off. It has to bring in combustion air, take out the heat the set rejects, and leave a person enough space to service the machine. Get the air and heat balance wrong and the set derates itself; get the access wrong and it cannot be maintained.
What the room has to do, in three lines
The room is not a shelter that happens to contain a generator. It is the last component in the combustion and cooling air system, and on an open frame set it also carries the noise and the weather protection that a canopy would otherwise provide. Three jobs, and they are best settled in this order: bring in enough clean air, take out enough heat, and leave enough space to work.
The order matters because the three jobs fight each other. A room lined to reduce noise adds resistance to the airflow. A room laid out for generous access costs air volume and lengthens the air path. A room sealed against sand and rain restricts the very opening that heat rejection depends on. Every decision in a plant room is a trade against one of the other two, and a layout that ignores one of them is re-opened after the first hot afternoon.
The two ways a room fails are worth naming, because they look nothing alike. The first is a thermal failure: the set runs, holds load, and then derates or trips as the room temperature climbs, usually in the hottest hour of the hottest month, and the fault is put down to the machine. The second is an access failure: nothing goes wrong for two years, because the set cannot be serviced properly, and then several things go wrong at once. Neither is exotic, and both are decided at the drawing stage rather than on site.
| Job | What it means in practice | What settles the figure |
|---|---|---|
| Combustion air | Clean, cool air the engine consumes, from its own opening | The engine datasheet combustion air figure, about 0.10-0.15 m3/s per 100 kW |
| Cooling air | Air that passes through the radiator and leaves again, carrying the cooling system heat | Radiator airflow at the site ambient, in m3/s, from the radiator datasheet |
| Heat rejection | Removing the heat that is not ducted out, plus the radiant heat that stays | The 5-10 % of rated kW left in the room when the radiator is ducted out |
| Service access | Space to change filters, clean the core, reach the battery and the panel, and lift the alternator | Clearances from the maintenance manual, and the largest part that has to leave the room |
Two air streams, and why they are not one
There are two air streams in a generator room, and they do different jobs. Combustion air is drawn into the engine, mixed with fuel and consumed; it is a small part of the total, and it has to be clean and as cool as the room allows. Cooling air passes through the radiator core, takes up the heat rejected by the jacket water and the charge cooler, and leaves the room. It is not consumed, it is a far larger volume, and its only job is to be able to travel in one side and out the other without coming back.
The commonest layout error is to treat them as one. A room with a single large louvre that serves both the radiator discharge and the combustion air intake makes the engine breathe air the radiator has just heated, and the mistake is invisible on a drawing: the louvre is the right size, the set is the right rating, and a commissioning test in winter passes. The same room in August shows a set that cannot reach its rating, and no amount of fuel system work will recover it, because nothing is wrong with the fuel system.
The second error is milder and just as common: an intake and a discharge on the same wall. Air leaving a discharge louvre at 2.5 to 5 m/s spreads along the wall and is drawn back into the intake a metre or two away. The room then recirculates a fraction of its own hot air continuously, the effective ambient rises by several degrees, and there is no obvious cause to point at. Where the two openings have to be on the same wall, they need real separation and, ideally, a divider or a discharge duct that carries the air away rather than letting it turn back.
| Air duty | What it does | Typical size | What goes wrong |
|---|---|---|---|
| Combustion air | Consumed by the engine | About 0.10-0.15 m3/s per 100 kW of engine output | Drawn from the radiator discharge, so the engine breathes pre-heated air |
| Cooling air | Through the radiator, not consumed | About 0.02-0.03 m3/s per kW, for a roughly 10 K rise | Restriction from undersized louvres, or an air path that turns back on itself |
| Room ventilation | Removes the heat left inside when the radiator is ducted out | Sized on the 5-10 % of rated kW that stays inside | Omitted, so the room becomes a heat trap with no hot-air outlet |
How much air the room has to move
The radiator airflow is the number the whole room is built around, and it comes from the engine or radiator datasheet, in cubic metres per second, at a stated ambient. Where the datasheet is not yet available, the budget figure is about 0.02 to 0.03 m3/s per kW of engine output for roughly a 10 K air temperature rise across the radiator, and it is good for a first pass rather than for a shop drawing.
Work it through on a 500 kVA set. At 0.8 power factor that is a 400 kW machine, and the figure that matters is the engine output, not the alternator kVA. Radiator airflow is then roughly 0.02 to 0.03 times 400, or about 8 to 12 m3/s, at the design ambient. Combustion air adds about 0.10 to 0.15 times 4, or 0.4 to 0.6 m3/s, taken from a separate opening. The radiator figure sizes the discharge louvre, the duct and the room opening; the combustion figure is the one that has to be kept away from the radiator discharge air.
The airflow then sets the openings, and openings are almost always underestimated, because the number on a louvre schedule is not the number that matters. A weather louvre passes air through its free area, which is typically about half of the frame size, and the design free area for a generator room is commonly put at 1.5 to 2.0 times the radiator core face area, on both the intake and the discharge. A louvre selected on its overall dimensions rather than on its free area restricts the air, raises the room temperature and, in the worst case, stalls the fan against a pressure it was never selected for.
| Quantity | Typical figure | How it is used |
|---|---|---|
| Radiator airflow | About 0.02-0.03 m3/s per kW of engine output, for roughly a 10 K air temperature rise | Sets the discharge louvre area and the duct cross-section |
| Combustion air | About 0.10-0.15 m3/s per 100 kW of engine output | Supplied from a source independent of the radiator air path |
| Heat to the room | About 5-10 % of the rated kW when the radiator is ducted out | Sizes the room ventilation when the radiator is not ducted |
| Louvre free area | 1.5-2.0 times the radiator core face area, on both intake and discharge | Read the free-area figure, not the frame size, on the louvre data sheet |
| Air velocity at louvres | 2.5-5 m/s | Above this the louvre itself becomes the noise source |
| Room temperature rise | Keep below 10 K above the outside ambient | Above that, the engine and alternator derating curves apply |
Ducted or free-blowing: what happens to the radiator air
Two arrangements are in normal use, and they change the whole heat balance. In a ducted room the radiator discharge is taken straight outside through a duct, and the room only has to handle the radiant heat, the alternator and the small leakage around the engine, which is the 5 to 10 % of rated kW in the budget table. In a free-blowing room the radiator discharges into the room itself, and the room becomes the plenum: the air then has to leave through an opening on the other side, and the space has to be large enough that the air is not turning a corner the moment it leaves the fan.
Ducting the radiator is the more common answer on an open set indoors, because it removes most of the heat at source and makes the room much easier to hold at the outside ambient. What it needs is the detail that is usually missing from a layout drawing: a flexible duct or a canvas sleeve between the radiator and the louvre, so that the set’s own vibration is not transmitted into the wall and the duct does not load the radiator; blanking plates so that air cannot spill around the duct and short-circuit back into the room; and a duct cross-section at least as large as the radiator face, with as few bends as the layout allows. A duct smaller than the core, or one that turns sharply, adds resistance the fan was never selected for, and the set pays for it in a lower rating.
Free-blowing rooms are simpler to build and stricter about layout. The air has to enter at one end and leave at the other, with the discharge above the set and the intake as low and as far away as the plan permits. The room volume has to absorb the fan’s throw, otherwise the air bounces off the far wall and returns to the radiator, and the set breathes its own discharge. Where the room is small relative to the airflow, which on a 500 kVA set at 8 to 12 m3/s it usually is, free-blowing needs either a larger room or more louvre area than a ducted design, and the trade should be a decision rather than an accident. The same choice reappears on a containerised set, where the enclosure is the room and the airflow path is fixed by the build.
Heat rejection, and how much of it stays in the room
The set rejects heat down four paths: through the radiator, out of the exhaust, by radiation from the engine block and the alternator, and by convection from the pipework and the warm surfaces inside the room. Only the first has an obvious route out of the building, and the design question is what happens to the other three.
The radiator carries the largest share, which is why ducting it out changes the room so much: once it is ducted, the heat left inside is commonly about 5 to 10 % of the rated kW, and the room ventilation is then sized on that figure rather than on the full cooling load. The exhaust is the second path and it leaves through the pipe, but the pipe itself radiates into the room along its whole length. An uninsulated exhaust run inside a plant room puts a real heat load into the space and raises the temperature at ceiling level, which is exactly where an intake louvre should not be. Insulating the run and discharging above roof level are the two decisions that keep that heat out of the room.
The radiant heat is small in absolute terms and easy to forget. The block, the alternator and the turbocharger radiate continuously, the pipework convects, and a room with no outlet for that heat will sit several kelvin above the outside air even with the radiator fully ducted. A room designed only for the ducted radiator, with no dedicated ventilation opening, fails in exactly the way the budget table warns about, and it fails as a set that never quite reaches its rating after several hours of running rather than as an obvious fault.
| Path | What it carries | What the design has to do |
|---|---|---|
| Radiator | The cooling system load, the largest single share | Duct it out, or size the room and its openings to carry the fan airflow |
| Exhaust | The exhaust gas, plus the heat radiated by the pipe itself | Insulate the run inside the room, and discharge above roof level |
| Engine and alternator radiation | A steady radiant and convective load from the surfaces | Provide room ventilation sized on the 5-10 % left inside, not only on the radiator |
| Pipework and surfaces | Convection from everything warm inside the space | Keep the ventilated volume moving, and avoid sealed pockets above the set |
The ambient inside the room is a de-rate you create
Every rating is declared against reference conditions, and the two that matter here are the engine reference of 25 °C at sea level and the ISO 8528-1 rating reference of 40 °C. Above the reference the engine loses roughly 1 to 2 % of its rated power per 5 °C, the alternator loses temperature margin because its rise is measured above the ambient, and the radiator loses cooling capacity because a hotter day leaves a smaller temperature difference to work with.
What makes this a room problem rather than a machine problem is that the room sets the ambient the set actually sees, and it is almost always higher than the weather. Recirculated air, stratification that leaves the ceiling hot, and an intake placed where the discharge has already warmed the air all add degrees that no datasheet anticipates. The budget figure for the room itself is to keep the rise above the outside ambient below 10 K, and where that cannot be met the engine and alternator de-rating curves have to be applied to the ambient the room actually delivers, not to the weather forecast.
The reason to be careful rather than pessimistic is that these losses multiply rather than add. A room that raises a 45 °C summer day by 8 K, on a site at 800 m of altitude, behind a radiator core that is a third fouled with dust, is de-rated on three counts at once, and the compounding is what turns a comfortable 500 kVA into a set that struggles in August. The honest order of work is to fix the room rise first, because it is usually the cheapest of the three to remove, and only then to price the machine against the conditions that remain. The method and the curves are set out in diesel generators for hot and humid climates.
| Figure | Value | What it means |
|---|---|---|
| Engine reference conditions | 25 °C at sea level, ISO 3046 | The ambient at which the rated power is declared, before any room effect |
| Rating reference | 40 °C, ISO 8528-1, for the declared class | The reference the performance class is stated against |
| Engine loss above reference | About 1-2 % of rated power per 5 °C | Multiplied, not added, with altitude and with radiator condition |
| Target room rise | Keep the room below 10 K above the outside ambient | Above this, the engine and alternator de-rating curves apply |
| Recirculation and stratification | Several kelvin, with no visible cause | Cured by separating the intake and the discharge, not by a larger machine |
The opening does three jobs: air, noise and weather
The room opening is where three requirements meet, and it is worth designing once against all three rather than three times against one. It has to pass enough air, it must not become the loudest part of the installation, and it has to keep the weather and the dust out.
On air, the free area is the figure that matters: 1.5 to 2.0 times the radiator face on both the intake and the discharge, with a face velocity at the louvre of about 2.5 to 5 m/s. Above roughly 5 m/s the louvre begins to generate its own noise as air passes the blades, so a louvre specified purely to keep the rain out often needs a larger frame than the airflow alone would suggest. On weather, the usual answer is a weather louvre with drainable blades, backed on a dusty or coastal site by a sand screen or a filtration panel that can be cleaned from outside without entering the room. Where dust and salt are both present the screen has to be maintainable, because a screen that is easier to fit than to clean will be left to blind itself, and a blinded screen is a restricted airflow whose effect arrives weeks later.
On noise, the room is an acoustic device whether or not it was designed as one. An untreated concrete room reflects sound, and reflections can add 3 dB or more compared with the same machine in the open. An absorbent lining, a lined door and acoustic louvres take that away, and on most installations the exhaust then becomes the dominant source once the room has been treated. The room treatment, the louvre and the silencer are one system rather than three items, and the figures behind them are in generator noise standards and attenuation. The point to carry into the layout is that a louvre selected only for airflow will undo an expensive acoustic build, and that the air path has to be drawn with the acoustic requirement already in it.
| Job | Figure | What goes wrong |
|---|---|---|
| Pass air | Free area 1.5-2.0 times the radiator core face, on intake and discharge | An undersized frame restricts the air and raises the room temperature |
| Stay quiet | Louvre face velocity about 2.5-5 m/s | A fast louvre becomes the dominant noise source at the boundary |
| Keep weather and dust out | Weather louvre with drainable blades, plus a removable sand screen | A screen that cannot be cleaned blinds itself and restricts the airflow |
Service access: what has to come in and what has to come out
Access is the part of a generator room that is decided last and regretted longest. It has two halves: the space to work on the machine day to day, and the route to get the machine, and the alternator, and the radiator, into and out of the building at the start and at the end of its life.
Day to day, the requirement is clear space at the radiator end and at the air intake, access on the service side for the filters, the battery and the control panel, and enough room at the fuel and cable entries to work with tools. The figure used on this site for the radiator end and the air intake is at least 1 m of clear space, plus access on the door side for servicing, and it is a minimum rather than a target. A set installed with 200 mm of clearance can be commissioned and run, but the first filter change, the first radiator cleaning and the first battery replacement all become a partial dismantling job, and the maintenance interval quietly stretches to match the access that exists rather than the one in the manual.
The other half is the heavy lift, and it is the half that is usually missing from the room. An alternator or a radiator change is a lifting operation, not a spanner job: the room needs either a fork-truck route and doors wide enough to pass the machine, or an overhead beam or crane of a stated capacity above the set, with enough height for the lift and the slings. The foundation, the plinth or the inertia block and the floor loading belong in the same conversation, because a room built for a 5 tonne set often cannot take the 8 tonne replacement, and a door sized for a pallet will not pass a radiator. The cable entry and the gland plate are part of the same list, and the sizing behind them is in generator cable sizing and voltage drop. Working this out at the drawing stage costs a wider door; working it out at the first overhaul costs a wall.
| Item | Typical requirement | Why it is decided early |
|---|---|---|
| Radiator and intake clearance | At least 1 m of clear space at the radiator end and the air intake | Without it the core cannot be cleaned and the fan performance changes |
| Service side | Access on the door side for filters, battery, panel and belts | It sets the room width; adding it later means moving the machine |
| Machine route | Doors or a fork-truck route wide enough to pass the set | The set has to get in and, one day, out again |
| Overhead lift | A beam or crane of stated capacity above the set for alternator and radiator changes | A heavy part cannot be hand-lifted out of a plant room |
| Foundation and floor | Plinth or inertia block sized to the set, with the floor loading checked | The room has to take the machine it will be asked to hold |
| Fuel, cable and exhaust | Reachable entries at the right levels, with the fill point accessible | These services are always run last and regretted first |
The mistakes that cost the most
The failures we see around generator rooms are rarely exotic, and most of them are decisions taken at the layout stage rather than at the machine.
| Mistake | What it costs | What prevents it |
|---|---|---|
| One louvre serving both the radiator discharge and the combustion air | A set that de-rates or trips in summer and will not hold load | Separate the two air paths, and take combustion air from clean, cool air |
| Intake and discharge on the same wall, close together | Continuous recirculation and a room that runs several kelvin hot | Real separation between the openings, or a duct that carries the discharge away |
| Louvre sized on frame dimensions rather than free area | A restricted air path, a hotter room and, in the worst case, fan stall | Read the free-area figure, and allow 1.5-2.0 times the radiator face |
| Radiator left unducted in a small room | The room becomes a heat trap and the set never reaches its rating | Duct the discharge out, or size the room as a plenum with the openings to match |
| Exhaust pipe left uninsulated inside the room | Radiant heat at ceiling level, right where the intake should not be | Insulate the run, and discharge above roof level |
| No clear space at the radiator or the service side | A set that cannot be cleaned or serviced, and an interval that stretches | The clearances from the manual, allowed for at the drawing stage |
| No overhead lift and no door wide enough for the machine | A wall opened at the first alternator or radiator change | Decide the heavy-lift route before the room is built |
Questions about generator room design
How much ventilation does a generator room need?
Two figures, and they are different sizes. Combustion air is about 0.10-0.15 m3/s per 100 kW of engine output, and it must come from its own opening rather than from the radiator discharge. Cooling air, the radiator airflow, is about 0.02-0.03 m3/s per kW of engine output for a roughly 10 K rise, so a 400 kW engine needs roughly 8 to 12 m3/s through the duct or the room. Size the opening on the radiator airflow and allow 1.5-2.0 times the radiator core face as free area, on both the intake and the discharge.
Can the radiator be ducted to the outside?
Yes, and on an indoor open set it is usually the right answer. Ducting takes the largest heat path straight out and leaves about 5-10 % of the rated kW in the room, which the room ventilation then has to remove. What it needs is a flexible duct or canvas sleeve so the set’s vibration is not carried into the wall, blanking plates so air cannot spill around the duct and short-circuit back into the room, and a duct at least as large as the radiator face with as few bends as possible.
Where should the air intake and the discharge be?
At opposite ends of the room, with the discharge high and the intake low, and never face to face on the same wall. Air leaving a louvre at 2.5-5 m/s spreads along a wall and is drawn back into an intake a metre or two away, so the room recirculates its own hot air and runs several kelvin hotter for no visible reason. If the two openings have to share a wall, allow real separation between them and add a discharge duct that carries the air away from the intake.
Does a bigger room always run cooler?
No. Volume helps a free-blowing room absorb the fan’s throw, but the air path matters more than the volume. A large room with the intake beside the discharge, or with the discharge short-circuiting straight back into the radiator, still runs hot. Fix the path first, and add volume only where the path is right and the air still has nowhere to go. On a 500 kVA set moving 8 to 12 m3/s, the room is usually small relative to the airflow, so the path is the lever that works.
How much clear space does a generator need for servicing?
At least 1 m of clear space at the radiator end and at the air intake, plus access on the door side for the filters, the battery and the control panel, is the minimum used here. To that add the sweep the door needs to open, room to reach the fill point and the cable entries, and either an overhead beam or a fork-truck route for the day an alternator or a radiator has to come out. A set with 200 mm of clearance can be commissioned, but it cannot really be maintained.
At what temperature does a generator start to de-rate?
It depends on the reference the rating was declared at. Engines are commonly rated at 25 °C at sea level to ISO 3046 and lose roughly 1-2 % of rated power per 5 °C above that, and ISO 8528-1 declares the performance class against 40 °C. A room that adds 10 K turns a comfortable figure into a de-rated one, and the room rise is usually the cheapest of the losses to remove, because it is fixed with openings rather than with a larger machine.
Can two generator sets share one room?
They can, and it is common in a data centre or a hospital, but the airflow has to be designed as a whole rather than twice. Each set needs its own intake and discharge path, or a layout that keeps one set’s discharge out of the other set’s intake; two sets sharing a common plenum warm each other, and the second set to start sees the hottest air and the lowest rating. Where the sets run in parallel the controls add their own requirements, which are set out in generator paralleling.
Send the room drawing, not only the kVA
Give us the room dimensions, where the intake and the discharge can be, the summer design ambient and the site altitude, the route the machine has to take into the building, and whether the radiator can be ducted out. The reply carries the airflow and the opening sizes the room has to provide, the ambient the set will actually see, and the build changes that follow from it.
Written and maintained by the KVA Grid sales engineering desk. The airflow and opening figures on this page are the planning figures published on the open frame range, and the effect of ambient temperature, humidity and dust on the set is set out in diesel generators for hot and humid climates. The room treatment and the silencer grade belong with generator noise standards and attenuation, the intervals the access has to serve are in the maintenance schedule, and fuel storage inside the room is covered in generator fuel tank, autonomy and fuel management. Room siting, fire separation, containment and inspection are settled by the local authority, the fire code and the insurer for the particular site, and the engine and radiator datasheets govern the airflow; this page describes general practice rather than a particular rule. Nothing on this page is a quotation for a particular project. Reviewed 12 October 2026.
