An IP rating tells you what an enclosure keeps out. It does not tell you how long the enclosure will last. On a coastal site those are two separate questions, and the second one, the corrosion class, is usually the one that decides the maintenance bill after five years.
What the IP code says, and what it does not
The IP code is IEC 60529 and it has two digits. The first digit covers solid objects and dust, the second covers water. IP23, the usual standard figure on a generator canopy, means protection against fingers and against water falling as rain at up to 60 degrees from the vertical. It does not mean dust-tight, and it does not mean the set can be hosed down.
What the code does not cover matters just as much on a generator. It says nothing about corrosion, salt, ultraviolet exposure, impact, condensation inside a panel, or how the enclosure behaves acoustically. Two canopies can both be called IP44 and have very different service lives two kilometres from the sea, because the second digit is a laboratory water test, and salt air is not a laboratory water test.
One more distinction is worth making early, because it appears in tenders. IEC 60529 is the enclosure code. IEC 60034-5 applies the same idea to rotating machines, which is why an alternator is quoted separately from the canopy. The automotive IP6K9K figure comes from a different standard again, ISO 20653, and a high-pressure-jet number borrowed from road vehicles does not make a generator enclosure better suited to the coast; the paint system and the fixings do that.
| Digit | Test it describes | What it means on a canopy or a container |
|---|---|---|
| First digit 2 | Fingers, and solid objects over 12.5 mm | The usual standard on a canopy: nobody can reach the live parts or the fan by accident |
| First digit 3 | Tools and wires over 2.5 mm | Needs a closed panel; a canopy with open louvres cannot claim it |
| First digit 4 | Wires over 1 mm | Normally stated for the control panel rather than for the machine room |
| First digit 5 | Dust protected: dust gets in but not enough to interfere | Commonly quoted for a container machine room with filters; the filter is then a service item |
| Second digit 3 | Spraying water up to 60 degrees from vertical | Rain on a vertical face; wind-driven rain at a low angle is a harder case than the test |
| Second digit 4 | Splashing water from any direction | The common coastal and dusty specification for a canopy, with the same rating on the glands and the panel |
| Second digit 5 | Water jets from a nozzle | Realistically a sealed container; it also reduces the ventilation opening, so the cooling package has to be designed as part of it |
| Second digit 6 | Heavy seas or strong jets | Rarely a generator requirement; where wave loading is real, the transport and the lifting arrangement matter more than the water digit |
| Rating | Typical build | Where it is asked for | What it still does not cover |
|---|---|---|---|
| IP23 | Standard canopy with rain hoods and louvres | Inland and sheltered sites; a fixed plant room already gives the same protection | Driven rain, dust, salt, hose-down; the alternator is quoted separately |
| IP44 | Weather louvres with drainable blades, gaskets on doors, sealed glands | Coastal and dusty sites; the usual minimum in the Gulf when the set stands outdoors | Fine dust over long periods, and standing water at the base if the drains are not kept clear |
| IP54 | Filtered ventilation, sealed panels, fully gasketed doors | Container machine rooms on remote or unattended sites | Corrosion: a sealed box still rusts from the inside out without a lining |
| IP55 | As IP54 with a higher water digit and a higher panel build | Container control rooms; panels that must be washed down | Nothing about acoustics, and nothing about the fixings that hold the panels on |
| Alternator IP23 or IP44 | IP23 as standard; IP44 with filters where dust is present | Quoted on the alternator datasheet, not on the canopy | A filtered alternator needs the filter changed; a blocked filter becomes a cooling fault |
The four jobs the enclosure is doing, and why they conflict
An enclosure is bought as one item and it is doing at least four jobs. They are specified separately, they are paid for separately, and they fail separately, which is why it helps to name them before choosing a rating.
The first is weather: rain, wind-driven rain, and sun. The second is dust and sand. The third is corrosion, which is a chemical job rather than a physical one and does not care about the IP digits at all. The fourth is noise, and on a set near a boundary it is often the job that decides the size and the cost of the whole enclosure. A fifth, which is not a protection job but competes for the same panels, is service access: doors, filter changes, and the room a technician needs to swing a spanner.
| Job | What it needs | What it fights |
|---|---|---|
| Weather | Overhangs, drainable louvres, sealed door edges, a roof that does not pond | Ventilation: every opening is a way in for water at a low angle |
| Dust and sand | Filters or screens ahead of the air path, and a way to clean them from outside | Cooling: a screen that is not cleaned becomes a restriction and then a de-rate |
| Corrosion | A paint or metal system matched to the exposure class, and the same class on fixings and hinges | Cost and repairability: a high build system costs more and is harder to touch up on site |
| Noise | Mass in the panels, absorbent lining in the cavity, and acoustic louvres | Airflow and water: lining absorbs water, and acoustic louvres restrict the air |
| Service access (not a protection job) | Doors that open fully, filters and belts reachable, the panel readable | Sealing: every door is a gasket that has to be kept in condition |
The practical consequence is that a specification cannot be met by asking for the highest number on every line. A dust-tight enclosure with no openings cannot cool the set, and an acoustic enclosure with a free air path cannot be quiet. What can be done is to decide which of the four the site actually needs, state it, and accept a known trade on the others.
Ventilation against protection: the trade that decides the build
The set has to move air whether or not it is inside a box. The planning figures are the same ones that apply to a plant room: a radiator airflow of about 0.02 to 0.03 m3/s per kW of engine output for roughly a 10 K air temperature rise, and combustion air of about 0.10 to 0.15 m3/s per 100 kW, taken from a source that is independent of the radiator discharge. Inside an enclosure the space is tighter than in a room, so the same air has to pass through a smaller opening, and the face velocity at the louvre is correspondingly higher.
That is the whole trade in one line. A larger free area passes the air easily and lets more water and dust in. A smaller opening keeps more of the weather out and raises the velocity, which raises the pressure drop across the louvre and the temperature inside the canopy, which costs rating. The published derating rules apply from the reference conditions the set was rated at, commonly 25 °C at sea level to ISO 3046, with roughly 1 to 2 % of rated power lost per 5 °C above that, and a restricted air path is one of the cheapest ways to create those degrees.
There is also an acoustic penalty hiding in the same opening. Above roughly 5 m/s a louvre starts to generate its own noise as the air passes the blades, which is why a louvre selected only to keep rain out frequently has to be larger than the airflow alone would suggest. Where a silencer and an acoustic louvre are both in the air path, the total restriction has to be checked against the fan curve rather than assumed, and the enclosure is then quoted with the de-rate that follows.
| Approach | Air path | Typical face velocity | What you give up |
|---|---|---|---|
| Open louvres, IP23 | Short and direct, low restriction | 2.5-5 m/s at the canopy opening | Driven rain and dust; no protection for the alternator beyond its own build |
| Weather louvres with drainable blades, IP44 | Blades shed water out of the airstream; slightly higher restriction | 5-8 m/s inside a canopy, where the opening is small | Opening area and a little fan margin; the blades need cleaning to keep draining |
| Weather louvre plus a removable sand screen | Two stages, both cleanable from outside | As above, with the screen added to the pressure drop | Servicing discipline: a screen that is easier to fit than to clean will blind itself |
| Filtered ventilation, IP54 | Air is drawn through an element before it reaches the set | Set by the filter face area, not by the louvre | The filter is now a scheduled item; a blocked filter is a cooling fault |
| Sealed and cooled, IP55 | No free opening; the heat leaves through a duct or a machine-cooled package | Not applicable | First cost, and any failure of the cooling package becomes a shutdown |
Corrosion is a climate number, not a paint name
Corrosion is specified with a different vocabulary from ingress protection, and mixing the two up is the commonest reason a coastal set looks protected on paper and is rusting inside two years. The exposure is classified by the corrosivity of the atmosphere, and the classification depends on two things that are measured rather than guessed: how much chloride is being deposited on the surface, and how much of the time the surface is wet.
The categories run from C1, a heated dry interior, to C5 for a high-salinity coastal or industrial atmosphere, with CX reserved for extreme cases such as offshore platforms and tropical marine sites with hydrogen sulphide present. A generator standing a kilometre from the sea, in a site with humidity most of the year, is not a C2 site with a nice canopy; it is a C5 exposure with a canopy that has to match it. The windward face is worse than the sheltered face, and the underside of the base is worse than the side panels, because that is where water and salt collect and stay.
The paint system is written separately from the category, as a corrosion category plus a durability class: a C5-M system is category C5 with medium durability, C5-H is the same exposure with a longer design life, and C5-VH is longer again. Reading the designation as one number, or as a brand of paint, is how a tender ends up comparing two quotes that are not offering the same thing. The category and the durability class should both appear in the specification, together with the surface preparation and the dry film thickness, because those are what decide whether the coating holds.
| Category | Typical environment | Typical build on a generator |
|---|---|---|
| C1, very low | Heated, dry interior with clean air | Standard canopy paint; the exposure is the least demanding one there is |
| C2, low | Inland, low pollution, short time of wetness | Standard canopy build with a galvanised shell and a powder coat |
| C3, medium | Urban or inland industrial atmosphere | Galvanised shell, powder coat, plated fasteners, and a coated base |
| C4, high | Coastal sites with moderate salinity, or industrial sites with pollution | A C4 paint system over blasted steel, stainless or plated fasteners, sealed glands |
| C5, very high | Within a few kilometres of the sea, high salinity, long time of wetness | A C5-M system as a minimum, galvanised or coated base, stainless fixings and hinges, coated radiator fins, and a touch-up routine |
| CX, extreme | Offshore, or tropical marine with hydrogen sulphide | Project-specific: duplex or fully stainless systems, GRP or composite fixings, and the buyer’s specification governs the whole build |
Materials and finishes that survive a coastal site
The order of work is the same at every exposure level: choose the material, then the coating, then the fixings, then the small parts, and make sure all four are in the same class. A canopy with a C5 paint system and plated hinges is a C5 canopy with a maintenance item built into it, and the hinges are the cheapest item on the list to get right.
On the shell, the common build is 1.5 to 2.0 mm galvanised steel with a polyester powder coat of 60 to 80 µm, which is the standard canopy figure on this site. Coastal sites move that up to a C4 or a C5-M paint system, and the details matter more than the headline number: cut edges, seams and any site-drilled hole are where corrosion starts, because the coating there is thinner or missing and the steel underneath is exposed. Where the exposure is offshore rather than merely coastal, GRP or composite fixings and a project-specific system replace the painted-steel assumption entirely.
Two material traps are worth naming. Aluminium panels do not rust, but they corrode quickly when they are bolted to steel in a wet, salty place, so the joint has to be isolated and the fasteners chosen for the couple rather than for their own strength. And stainless is not one material: 304 is adequate inland and can pit in coastal chlorides, so a coastal or offshore site generally moves to a 316 grade for the fixings and the exposed hardware.
| Component | Standard build | Coastal build | Why this one matters |
|---|---|---|---|
| Shell and panels | 1.5-2.0 mm galvanised steel, polyester powder coat 60-80 µm | The same shell with a C4 or C5-M system and a higher build at the cut edges and seams | Corrosion starts where the coating is thinnest, which is every cut edge and every site-drilled hole |
| Base frame or base tank | Painted steel, standing on a slab | Galvanised or coated base, raised and drained so water does not stand against it | The underside sees the longest time of wetness and is inspected the least |
| Fasteners, hinges, latches | Plated steel | Stainless, or plated to the same class as the shell | The first parts to fail and the cheapest to upgrade; one plated hinge undoes the class |
| Door seals and gaskets | Standard EPDM profile | The same profile, checked and replaced as a service item | A perished seal makes an IP44 claim untrue without changing a single number on the datasheet |
| Radiator core and fins | Standard core, cleaned on schedule | Coated fins where the site is coastal, with the same cleaning interval | Salt and damp dust cake between the fins, which is both a corrosion site and a cooling fault |
| Cable entries and glands | Standard glands on a gland plate | Sealed glands quoted at the same IP as the enclosure | An enclosure is only as good as its weakest gland, and the gland is usually the weakest one |
| Control panel | IP-rated panel as quoted | The same panel with an anti-condensation heater | A panel that cools overnight draws damp air in, and the fault shows up as electronics rather than as rust |
| Alternator | IP23 as standard | IP23 with an anti-condensation heater, or IP44 with filters where dust is present | Windings fail from moisture and from dust long before the frame rusts through |
The small parts that fail first
Almost nothing on a coastal set fails as a panel. It fails as a gland, a gasket, a hinge, a bolt, a drain plug or a label plate, and each of those is a small line item that is easy to leave at the standard build when the specification moves to a coastal class. The failure is also slow enough to be missed: the enclosure still looks sound, the set still runs, and the first sign is water in the panel or a rust stain under a door.
The principle to hold on to is that the enclosure is only as good as its weakest gland. A canopy built to IP44 with standard cable entries is an IP23 canopy with a better roof, because water and dust enter through the entry rather than through the panel. The same logic applies to the panel itself: an IP-rated control panel that is opened on site and closed without its gasket seated is no longer the panel that was quoted.
| Item | How it fails | Coastal specification | When it is checked |
|---|---|---|---|
| Cable glands and entry plate | Water tracks down the cable and into the enclosure; the gland corrodes at the thread | Sealed glands at the same IP as the enclosure, on a gland plate that is coated with the shell | At commissioning and at every cable or panel intervention |
| Door seals and gaskets | Perishes in the sun and stops sealing; the door is then closed on a hard gasket and left | UV-stable profile, replaced as a consumable rather than as a repair | At each scheduled service; replace when the profile is hard or flat |
| Hinges, latches and their fixings | Rust at the pin, which then seizes, and the door is left ajar or forced | Stainless hinges and latches, or plated to the same corrosion class as the shell | At each service, with a drop of lubricant on the pin |
| Drains and low points | Block with dust and the enclosure holds water at the base, under the tank and against the frame | Drained low points, screened so debris cannot plug them, kept clear | At each service, and after any dust storm or heavy rain |
| Fasteners on the shell | Corrode from the head inwards; the panel is then difficult to remove without damage | Stainless, or plated to the shell’s class, with the same grade throughout | At each service; replace, do not re-paint over |
| Touch-up paint and its record | A scratch or a stone chip becomes a corrosion site within one season on a coastal site | A touch-up kit in the same system as the coating, and a line in the service sheet | At each service, and after any transport or site damage |
| Labels, nameplates and cable markers | Fade, lift and then trap water against the panel | Coastal-grade plate and adhesive, or plates fixed on stainless | At each service; a lifting label is a leak path |
Acoustic linings, drains and the water that stays inside
The quietest enclosures and the driest enclosures are built in opposite directions, and the site that needs both needs the detail designed rather than assumed. A canopy that carries absorbent lining in its cavity is carrying a material whose whole job is to present a large internal surface area, and a large internal surface area in a humid, salty place is where water and salt will sit if nothing is done about it.
In practice the lining is protected by a perforated face, the cavity is arranged so that any water that does get in can drain out rather than pool against the lining, and the low points have drains that are accessible from outside and cleaned on a schedule. The acoustic louvres are the same compromise in a different shape: they restrict the air path, they collect dust on their splitters, and their drainage depends on the blades being clean enough to shed water. When the lining is wet, two things happen at once, and neither is obvious from the outside: the attenuation the enclosure was bought for drops, and the wet surface starts to attack the fixings that hold the lining in place.
That is the reason a coastal specification includes the maintenance interval as a design input rather than an afterthought. If the drains cannot be reached without tools, or the louvres cannot be cleaned without scaffolding, the interval that actually happens will be longer than the one in the manual, and the acoustic and corrosion performance both follow the interval that actually happens.
What we specify for a coastal site
This is an illustrative specification, not a delivered project. It shows how the exposure class and the site conditions turn into a build sheet. Replace the figures with your own site data before pricing.
| Item | Example specification | Why it is written that way |
|---|---|---|
| Exposure | C5 corrosivity, long time of wetness; paint system stated as C5-M | The category comes from the site, and the durability class is stated separately so two quotes can be compared |
| Enclosure | Canopy at IP44, with weather louvres having drainable blades and a removable sand screen | IP23 does not survive driven rain on the coast; the screen has to be cleanable from outside |
| Air path | Separate combustion air intake, radiator discharge hooded and directed away from the intake | Recirculation adds degrees, and degrees cost rating before the paint system is even considered |
| Base | Coated or galvanised base tank, raised off the plinth, drained, with the fill point accessible | The base has the longest time of wetness and the shortest inspection attention |
| Fixings and hardware | 316 stainless hinges, latches and external fasteners; isolated joints where aluminium meets steel | The cheapest upgrade on the list and the one that most often gets left out |
| Alternator and panel | Alternator IP23 with an anti-condensation heater, panel at the enclosure IP with its own heater | Moisture and dust fail windings and electronics long before the frame fails |
| Acoustics | Lined canopy with a protected lining face, or an acoustic louvre where the boundary requires it | The acoustic build has to be specified together with its drainage, not after it |
| Maintenance | Louvre and screen cleaning, drain clearing and a touch-up walk-round at the scheduled interval | The protection is a routine, not a one-off purchase |
| Stated de-rate | Rating quoted at the site ambient with the enclosure in place | The enclosure restricts the air path, so the enclosed rating is the number that applies |
The mistakes that cost the most
The expensive mistakes on an enclosure are rarely exotic, and most of them are made when the specification is written rather than when the set is built.
| Mistake | What it costs | What prevents it |
|---|---|---|
| Specifying the IP number on the canopy and leaving the glands at the standard build | Water and dust in the panel on the first storm; a protection claim that is not true in service | Quote the glands, entries and panel at the same IP as the enclosure, and check them at commissioning |
| A coastal paint system on the panels with plated hinges and fasteners | Rust at the hinge line and the door edge within a few seasons, in the most visible place | Put every fixing, hinge and latch in the same corrosion class as the shell |
| Asking for dust-tight without checking the airflow | A restricted air path, a hotter enclosure and a set that cannot reach its rating in summer | Size the opening on the radiator airflow, then decide how much protection that size allows |
| Reading the IP rating as a corrosion rating | A well-sealed enclosure that is still rusting from the inside, and a maintenance bill nobody budgeted for | Write the corrosivity category and the paint system as separate lines in the specification |
| A sand screen that is easier to fit than to clean | The screen blinds itself, the airflow falls away, and the fault appears weeks later as a hot set | A screen removable and cleanable from outside without entering the enclosure |
| Acoustic lining with no drainage path | Wet lining: the attenuation drops and the fixings that hold the lining corrode | Protect the lining face, drain the cavity, and make the low points reachable |
| A painted base tank standing in water | Corrosion of the base and eventually of the tank, which is the most expensive panel to replace | Coated or galvanised base, raised off the slab and drained |
| Comparing two quotations on the IP number alone | Two prices that are not for the same build, and a decision made on the wrong line | Compare the category, the durability class, the fixings and the alternator build together |
| Touching up with whatever paint is on the shelf | A repair that fails faster than the damage it was meant to cover, and no record of what was done | A touch-up kit in the original system, and one line in the service sheet each visit |
Questions about enclosure IP rating and corrosion
Is IP44 enough for a coastal site?
It is the usual minimum for a canopy standing outdoors, and on this site IP23 is the standard build while coastal and dusty sites move to IP44 or better. But the IP number only settles the water and dust question. The service life of a coastal set is decided more by the corrosion class, the paint system and the fixings than by the second digit, so an IP44 canopy with standard glands and plated hinges is not a coastal build, whatever the datasheet line says.
Does a higher IP rating mean better corrosion protection?
No, and it is worth being firm about this because the two are constantly mixed up. The IP code comes from IEC 60529 and tests solids and water. Corrosion is classified by the corrosivity of the atmosphere and by the protective system applied to the steel, which is a different pair of standards. A sealed enclosure can still rust from the inside out, because condensation forms on the inside of a sealed box just as readily as on the outside of an open one.
What does a designation such as C5-M actually mean?
It is two things in one line. C5 is the corrosivity category of the environment, in this case a high-salinity or industrial atmosphere, and the letter is the durability class of the paint system, where M is medium, H is high and VH is very high. The category comes from the site, and the durability class comes from the buyer’s requirement. Reading the C5 as if it were the whole specification, without the surface preparation and the dry film thickness, is how two quotations that are not equivalent end up looking identical.
Can an open set be used on a coastal site?
Yes, and it is common in the Gulf: the set stands in a plant room and the room is the weather protection. What changes is that the room then has to do the corrosion work instead of the canopy, so the same questions about the fixings, the coating, the base and the drainage apply to the building rather than to the enclosure. The room also has to handle the airflow, which is set out in generator room design.
How much rating does the enclosure cost?
Whatever the restricted air path costs in internal ambient. The closed enclosure is a smaller opening than a plant room wall, the face velocity at the louvre is higher, and the temperature inside the canopy is above the outside air as a result. The rating should therefore be quoted at the site ambient with the enclosure in place rather than at the reference conditions: engines are commonly rated at 25 °C at sea level to ISO 3046 and lose roughly 1 to 2 % of rated power per 5 °C above that, and the enclosure is one of the things that creates those degrees.
How often does a coastal enclosure need attention?
The interval is set by the site and written into the maintenance schedule, but two items decide whether the rest of the routine works at all: the louvres and screens have to be cleaned from outside, and the drains have to be cleared. If either needs tools, height access or a shutdown to reach, the interval that happens in practice will be longer than the one in the manual, and both the acoustics and the corrosion will follow the interval that happens.
What do you need in order to quote enclosure protection?
Six things: the distance from the sea and whether the site is coastal, offshore or inland; the design ambient, the humidity and how much dust and sand the site sees; whether the set stands outdoors, under a roof or inside a room; the noise limit at the nearest receptor; whether the enclosure has to be hosed or washed down; and the buyer’s own paint system or corrosion class if one is specified. Those six answers fix the enclosure, the coating, the fixings and the stated de-rate.
Send the site location, not only the kVA
Tell us how far the set will stand from the sea, what the summer ambient, humidity and dust are, whether it stands outdoors or inside a room, and what noise limit applies at the nearest boundary. The reply carries the enclosure rating, the corrosion class and paint system, the fixings and the de-rate that follow from the enclosure.
Written and maintained by the KVA Grid sales engineering desk. The enclosure figures on this page — IP23 as standard, IP44 for coastal and dusty sites, IP54 for a container machine room and IP55 for its control room, the 1.5-2.0 mm galvanised shell with a 60-80 µm powder coat, and the ingress ratings quoted on the alternator — are the values published on the silent range, the containerised range and in silent and open frame compared. The effect of ambient temperature, humidity and salt on the set is set out in diesel generators for hot and humid climates, the acoustic build in generator noise standards and attenuation, the airflow the enclosure has to pass in generator room design, the intervals in the maintenance schedule, and the coastal and offshore case in oil and gas sites. Exposure classes follow ISO 9223, protective paint systems ISO 12944 and sound measurement ISO 8528-10; the exposure at a particular site and the buyer’s specification govern what is built. This page describes general practice rather than a particular rule, and nothing on it is a quotation for a particular project. Reviewed 16 October 2026.
