A diesel generator that spends its life waiting for a power cut has a problem the hour meter cannot show. It runs, it starts on the first crank, and it still fails the one job it was bought for. The reason is usually the load it never carried: a set that idles or runs at a small fraction of its rating leaves unburnt fuel and soot in the exhaust, and over months that deposit turns into wet stacking.
This guide explains what the deposit is, why standby sets are the ones that get it, how to recognise it before it costs an engine, and how to clear it without replacing parts.
What wet stacking actually is
In a diesel engine, the fuel that is injected has to burn. At load, the cylinder is hot enough and the charge is dense enough that nearly all of it does. At light load the combustion temperature falls, some of the fuel does not complete the burn, and the exhaust carries it out as a wet, oily film rather than as gas. That film condenses on the coolest surfaces it meets: the exhaust manifold, the turbocharger, the silencer, the stack, and on the after-treatment elements if the set has them.
The result is a black, sticky coating that looks like heavy soot but behaves like tar. It is not a fuel problem and it is not a filtration problem. It is an operating-pattern problem, and the only reliable way to prevent it is to change the pattern.
Why standby sets are the ones that get it
Two habits produce it. The first is the weekly no-load start: the set runs for ten or fifteen minutes, gets warm on the outside but never reaches working temperature inside, and is shut down again. The second is the real thing — an outage where the set carries a lighting and socket load that is a small share of what it was bought for.
Neither is negligence. Both are how standby systems are normally run. The deposit builds slowly, which is exactly why it is missed.
| Operating pattern | What happens inside the engine | What builds up |
|---|---|---|
| Weekly start with no load | Combustion stays cool, the block warms slowly, the set is stopped before it is properly hot | A thin wet film that never burns off |
| Outages at a small fraction of rating | The set carries the essential bus only, so it never gets near the load it was sized for | Soot and unburnt fuel through the manifold and silencer |
| Long idle periods between starts | Condensation forms in the exhaust and the crankcase, and the oil never gets hot enough to shed it | Moisture under the deposit, which is what turns it sticky |
| Repeated short runs on a cold engine | Ring sealing is poor until the engine is hot, so blow-by is high for most of the run | Crankcase contamination and faster oil degradation |
Signs you can see and hear
The first sign is usually at the stack: a dark, wet-looking plume that keeps coming after the set has been running for a while, and a smell that is closer to raw fuel than to normal exhaust. Around the manifold and turbo the deposit shows as an oily black film that wipes off rather than brushing away as dry soot.
Later signs are mechanical. The set becomes harder to start, hunts slightly at no load, and smokes more heavily for longer after each start. On a turbocharged set the boost may come up more slowly, and the exhaust note changes as the silencer fills. If the deposit has reached the point where it is bridging an after-treatment element, the set will report a back-pressure or regeneration fault before it reports anything about the load.
What it does to the engine over time
Wet stacking is not cosmetic. Every surface it coats changes how the engine next runs.
| Where it collects | Effect over time |
|---|---|
| Exhaust manifold and turbocharger | Reduced gas flow, slower turbo response, higher exhaust temperature at the same load |
| Silencer and stack | Restriction and a heavier smoke signature; in bad cases the deposit ignites inside the silencer |
| After-treatment elements | Blocked passages, failed regeneration, and a back-pressure fault that persists after the load problem is solved |
| Cylinder walls and rings | Glazing and stuck rings, which is the point where the engine stops sealing and starts burning oil |
| Crankcase oil | Soot loading and fuel dilution, which thins the oil and shortens the interval it can be trusted for |
After-treatment makes it worse, and hides it longer
A set with a diesel particulate filter or selective catalytic reduction system gives the operator a false sense of protection. The filter captures the soot, so the stack looks clean while the engine is still producing it. The system then tries to burn the captured soot off in a regeneration cycle, and regeneration needs exhaust temperature that a lightly loaded set cannot produce on its own.
The result is a repeating cycle of partial regenerations, rising back-pressure, and eventually a derate. Back-pressure and regeneration behaviour is worth understanding before blaming the after-treatment itself: on most standby sites the element failed because it was asked to deal with an operating pattern it was never specified for.
How to clear it
The cure is heat and load, applied deliberately. Bring the set up to working temperature and hold it there under a real load long enough for the exhaust to burn the deposit off. On a set with a modest amount of build-up that is a scheduled loaded run; on a set that has been on standby for years it is a load test with someone watching the exhaust temperature, the boost and the back-pressure.
A load bank exists for exactly this: it gives the set a load that the building cannot provide, at a level and duration the test plan sets, without putting the site at risk. Resistive load raises exhaust temperature and clears soft deposit; it does not fix glazed cylinders, stuck rings or a filter that has already failed.
What it should not be cleared with is a bottle of additive and a long idle. Additives change how the deposit forms at the margin; they do not remove what is already in the silencer, and idling is the condition that created it.
Setting a load policy that prevents it
Prevention is a schedule, not a habit. The starting point is to know what share of its rating the set actually carries during a real outage, because that number decides everything else. A set that runs essential circuits only, on a site sized for a much larger load, will always be working below the range where a diesel engine runs cleanly.
The practical measures are to run a loaded test on a fixed interval rather than only a no-load start, to log the load carried during real outages from the controller, and to size the replacement set against the load actually connected rather than the load the building could draw. Where the load is genuinely small, a smaller set running at a sensible share of its rating is a better answer than a large set idling. Prime and standby ratings are defined around sustained load, and a standby rating is not a licence to run the set below its own working range for years.
Recording the load during each outage, and comparing it with the service schedule and the fuel consumption the site expects, turns an invisible problem into a trend line.
What wet stacking is not
Not every smoking set is wet stacking. A set that smokes under load, or that smokes white rather than dark, has a different problem — an injector, a turbo seal, coolant, or an air restriction. A set that is hard to start after months of standing may simply have a flat battery or fuel that has been sitting in the tank.
It is also not a fault that a warranty claim can settle. The engine did what it was asked to do; it was asked to run outside the range it was built for. Which is why the fix belongs in the operating plan, and why a used set with a long standby history deserves a bore and exhaust inspection before it is bought.
Questions buyers ask about wet stacking
How much load does a generator need to avoid wet stacking?
Enough to hold combustion temperature at the level the engine was designed for. That is a share of rating rather than a fixed number, and it differs between engines, so the figure to work from is the maker’s own guidance for the model, checked against the load the site actually carries.
Can a weekly no-load run cause it?
On its own, a short no-load run does not create much deposit, but it does not clear any either, and it adds condensation. A weekly run that never reaches temperature is maintenance in name only; the loaded test is what keeps the set honest.
Does the smoke mean the engine is worn out?
Not necessarily. Dark wet smoke after a long light-load period is the classic sign of deposit burning off, and it should reduce as the set works under load. Smoke that continues at full load, or that comes with a rise in oil consumption, points at wear or an injector.
Will a load bank damage an engine with heavy build-up?
It can if it is applied carelessly. Loose deposit that breaks away can reach the turbo or the after-treatment in a lump. A set with a long history of light-load running is loaded gradually, with exhaust temperature and back-pressure watched, and stopped if either runs away.
Is a smaller generator the answer for a lightly loaded site?
Often, yes. A set that carries a proper share of its rating runs cleaner, burns less fuel per kWh delivered and needs less intervention. The trade-off is that it has less headroom for motor starting, so the starting load has to be checked before the rating is reduced.
Does the deposit ever clean itself?
Soft deposit burns off when the set works hard and hot for long enough. Hard, glazed deposit on cylinder walls and rings does not, and neither does a filter element that has been blocked. Those are inspection and repair items, not operating items.
Next step
If a standby set has been on light load for a season, the useful first action is to log the load it actually carries and then give it a loaded run with the exhaust watched. That answers the question the hour meter cannot.
Send the set’s rating, the load it carries during an outage and the hours it has run, and we will say whether the pattern is likely to be a problem on that machine and what the next test should be.
