A day tank is usually drawn as a small rectangle beside the generator, but it is where bulk storage becomes an engine fuel system. Its elevation sets inlet pressure, its return connection decides where surplus fuel and air go, and its level controls decide whether the transfer pump fills it or floods it. Most day tank failures are layout failures: the tank is the right size, but the head is wrong at low level, the return is too small, or the overflow has nowhere safe to go.
The short answer: a day tank is a hydraulic boundary
The main tank stores fuel; the day tank keeps a smaller volume close to the engine. That proximity shortens the suction path and gives the set a known, local supply. The useful part of the arrangement is hydraulic: the day tank fixes the inlet pressure the engine sees, gives air and water a place to settle, and separates the engine return from bulk storage. If any of those functions is left to chance, the set may run at no load and still fail when it has to carry the site.
The layout choice sets the worst case. A gravity tank has its lowest head when nearly empty; a pump-fed tank has its highest pressure when the regulator fails closed; an integral base tank may sit below the inlet and trap air. The return is not a drain either: at light load the engine returns far more fuel than it burns, so the line must be sized for return flow, not burn rate. The level sequence decides when the transfer pump starts, when it stops, and which device stops a delivery.
| Function | What it means in practice | Layout consequence |
|---|---|---|
| Buffer volume | Keeps a local fuel reserve close to the engine and shortens the suction path | The usable volume between the low-level alarm and the high-level stop has to cover the autonomy the project requires |
| Hydraulic reference | Sets the inlet head at the engine, from full tank to low level | Elevation, pipe route, strainer and fittings must be checked at the worst case, not at a full tank |
| Air and water separation | Gives vapour and entrained air a place to leave the fuel and gives water and sediment a low point | The tank needs a correct vent, a settling volume and a drain that can be used without opening the fuel path |
| Transfer boundary | Separates the engine return and the bulk tank from the engine supply | The return, overflow and vent are separate circuits, each with its own route and its own failure mode |
Layout: elevation, footprint and the route that decides both
Start at the engine inlet, not at the tank. Mark the inlet, the return and the highest point of the fuel system on the drawing, then place the tank so the supply route falls continuously to the engine, or rises continuously if the tank is below the inlet. A route that rises and falls creates an air trap. The trap may pass fuel at commissioning and collect air weeks later, which is why a set can run cleanly after a service and then falter on the next load test.
The footprint has to leave access to the level switches, drain, strainer, return connection and vent. A tank pushed into a corner may meet the volume requirement and still be unmaintainable. The drawing should also show the vent termination, overflow route and spill containment, because those decide where vapour can collect and where fuel goes if a level control fails.
Elevation has the largest effect on the engine. A gravity tank is simple and has no transfer pump in the supply path, but its head changes as the tank empties; it must be high enough at the low-level alarm, not at the full level. A tank at grade needs a pump and regulator, and the regulator then defines the inlet pressure. An integral base tank is compact, but a high loop over the frame can undo the advantage of a short suction.
Keep supply and return connections apart inside the tank. A return discharging next to the suction sends aerated fuel back to the engine; one discharging above the fuel level can foam the surface and make the gauge unreliable. The usual detail is a return that enters the top and discharges below normal fuel level, falling continuously back to the tank. Confirm the termination with both manufacturers.
| Arrangement | How fuel reaches the engine | Head at the inlet | Main layout risk |
|---|---|---|---|
| Elevated gravity tank | By static head through a falling supply line | Highest when full, lowest at the low-level alarm | Too little head at low level, or a structural load that was never checked |
| Day tank at grade with transfer pump | Pump and regulator, or a level-controlled pump | Set by the regulator or the pump curve | Pump deadhead, regulator failure, or a return path that cannot relieve excess flow |
| Integral base tank | Short suction from the base frame | Small static head; may be negative at low level | Trapped air, poor access, and a suction strainer that is difficult to clean |
| Pressurised day tank | Pump maintains pressure in the tank or loop | Controlled, but only while the relief path works | Overpressure, relief discharge route, and a tank not built for the pressure |
Head pressure: what the engine sees at the inlet
The engine fuel inlet has a working pressure window. Below the minimum, the injection pump can cavitate, the engine may lose power or fail to start, and the system may draw air through a joint that is tight at atmospheric pressure. Above the maximum, the pump seals and regulator are asked to absorb pressure they were not designed for, and return flow can rise. The window is specific to the engine and fuel system; use the manufacturer’s inlet pressure range and check it at the lowest normal fuel level.
The head budget starts with static elevation, measured from the lowest normal fuel level to the centreline of the engine inlet. If the tank is above the inlet, elevation adds pressure; if it is below, elevation subtracts it. For diesel, each metre of static elevation adds roughly 8 kPa, but the actual figure depends on fuel density and temperature. That static term is only the beginning: the supply line, strainer, valves, elbows and check valve all take pressure away as fuel flows.
Friction is not fixed. It rises with flow and with the condition of the strainer. A calculation that uses a clean strainer and full-load draw may look acceptable and fail when the element is partly loaded or the fuel is cold. Check the pressure drop at maximum flow with the strainer in its dirty condition, using the longest route and worst combination of fittings shown on the drawing. The return line has its own backpressure limit, set by return flow, bore, elevation and termination, not by the burn rate.
| Item | Effect at the engine inlet | What to use in the check |
|---|---|---|
| Static elevation | Adds pressure when the tank is above the inlet; subtracts when it is below | Lowest normal fuel level to inlet centreline, with the actual fuel density |
| Supply pipe friction | Subtracts pressure as flow rises | Maximum engine draw, longest route and the actual pipe bore |
| Strainer or filter | Subtracts pressure; the loss grows as the element loads | Dirty-element pressure drop at maximum flow, not the clean figure |
| Valves, elbows and fittings | Each adds loss and can trap air | The as-built route, including the fittings that were added on site |
| Check valve | Subtracts its cracking pressure and may chatter at low flow | Manufacturer’s cracking pressure and the flow range of the engine |
| Regulator or float control | Sets or limits the downstream pressure | The controlled pressure range and the failure position |
Return lines: where the fuel goes when it is not burned
The engine return is not a drain. It carries fuel from the injection pump and injectors back to the tank, and at light load it can be a large fraction of the fuel that leaves the day tank. The line must carry that flow without raising the pressure in the injection pump case above its limit. A return sized on consumption, or on the supply line size, can be too small at full load. Use the manufacturer’s maximum return flow, allowable backpressure and highest expected fuel temperature.
Route the return so it falls continuously back to the day tank. A high point becomes an air pocket; a low point becomes a water and sediment trap; a line that rises after a long horizontal run can hold fuel and surge when the engine stops. The return should enter away from the suction, below normal fuel level where the manufacturer permits, through a termination that does not splash or foam. If it must rise above the tank, add a loop or check arrangement that prevents back-siphon and confirm the detail with both manufacturers.
The day tank also needs an overflow or spill path that is separate from the engine return and the vent. The overflow is sized for the maximum transfer pump flow, because its job is to pass the output of a pump that has not yet stopped. It should be visible or alarmed and lead to a safe, contained location. Combining overflow with the vent is a common error: the vent is sized for breathing and fill rate, while the overflow must pass liquid. A combined pipe can turn a pump fault into a pressure event or a spill.
Prove the return with pressure, not appearance. Fit test points at the engine connection and tank end, then record the difference at full load. A reading above the manufacturer’s limit points to a closed valve, collapsed hose, return strainer, high point or a line reduced at a hose barb. Correct the route or bore; do not raise the return pressure limit.
| Circuit | What flows | Sizing basis | Common mistake |
|---|---|---|---|
| Engine fuel return | Surplus fuel from the injection system, hot and possibly aerated | Maximum return flow at full load and the manufacturer’s allowable backpressure | Sized on the engine’s burn rate or on the supply pipe size |
| Day tank overflow or spill | Excess fuel from a transfer pump or a failed level control | Maximum transfer pump flow, with a safe and contained destination | Combined with the vent or left to discharge where it cannot be seen |
| Tank vent | Air and vapour during filling, draw-off and thermal breathing | Maximum fill rate, maximum draw-off and allowable tank pressure | Treated as a drain or fitted with a restriction that blocks breathing |
| Drain and water draw-off | Water, sediment and a small fuel sample | The lowest point of the tank and a contained sample point | No access, or a drain that cannot be operated without opening the fuel path |
Sizing the tank and the transfer path from real flows
Size the day tank from the autonomy the project requires, then check that the usable volume is actually available between the low-level alarm and the high-level stop. A nominal volume that includes an unusable heel, a raised suction and a high-level margin can deliver much less than its nameplate. The usable volume is the figure that matters for an outage, and it should be shown with the alarm levels that define it.
The published fuel figures give a useful check. A 500 kVA set uses 101 litres an hour at full load, 80 litres an hour at 75 % and 60 litres an hour at 50 %. A 1000 kVA set uses about 200 litres an hour at full load, and about 4800 litres over 24 hours. The general range is 0.24 to 0.29 litres per delivered kWh, so consumption follows load rather than nameplate. A day tank sized for an eight-hour run at full load on a 1000 kVA set would need about 1600 litres of usable volume; at half load it would need about 800 litres. The eight-hour figure is an example assumption, not a rule: the autonomy target is set by the project specification.
The transfer pump must refill the tank while the engine runs, without deadheading at high level. Its flow is usually above maximum consumption, with a margin set by the manufacturer’s data and the project specification. Give it a defined start level, stop level and protected path for excess flow. A pump allowed to run against a closed valve, or restarted before the level has fallen enough, will fail early or make the indication unstable.
The circuits are connected: the return sets the backpressure limit, the overflow sets the maximum spill flow, the vent sets the tank pressure limit, and the supply line sets the inlet head. A larger transfer pump needs an overflow check; a rerouted return, a check for high points; a raised tank, a check of inlet maximum as well as minimum.
| Set and load | Fuel consumption | Usable volume for 8 hours | What the example shows |
|---|---|---|---|
| 500 kVA at full load | 101 L/h | About 808 L | The tank has to cover the highest published consumption, not an average |
| 500 kVA at 75 % load | 80 L/h | About 640 L | A lower load reduces the volume but not the need for a correct low-level head |
| 500 kVA at 50 % load | 60 L/h | About 480 L | Light-load running is inefficient and does not remove the need for a load test |
| 1000 kVA at full load | About 200 L/h | About 1600 L | A 24-hour run would need about 4800 L, which belongs in the main tank, not a day tank |
Level control, alarms and the edge of the tank
Write the level sequence as a table before it is programmed: low-low to protect the engine, low to start the transfer pump, high to stop it, and high-high to alarm and stop a delivery. The exact setpoints are set by the manufacturer’s data and the project specification, but the high-high should be independent of the normal level transmitter. A single float that both controls the pump and provides the high alarm gives no protection when it sticks.
Test by simulation, not only by filling. Drive each input and confirm the output at the pump, panel and fill point. A broken cable, lost signal or stuck float should produce a safe state, not a silent one. The high-high alarm must be audible at the fill point and distinguishable from the normal high-level stop. If the site has remote monitoring, confirm the alarm reaches someone who can act.
The tank edge matters as much as the panel. Keep the vent clear, the overflow visible and the drain accessible without standing under the tank. Keep the fill connection separate from the vent and arrange the fill point so a delivery can be stopped before the tank is full. These details connect to vent and overfill protection and to the bonding review at the fill point.
| Check | Method | Acceptance basis |
|---|---|---|
| Supply head at low level | Measure at the engine inlet with the tank at its low-level alarm and the set at full load | The engine manufacturer’s inlet pressure window |
| Return backpressure | Measure across the return line at full load and at the highest expected fuel temperature | The engine manufacturer’s allowable return pressure |
| Level sequence | Simulate low, low-low, high and high-high inputs and record each output | The approved control narrative and project setpoints |
| Transfer pump | Check start, stop, deadhead protection and overflow with the engine running | The pump and project specification |
| Alarm annunciation | Confirm local and remote alarms, including the fill-point alarm | The project alarm schedule |
| Annual load test | Run the set at 50 % to 100 % of rating once a year and repeat the pressure checks | The site maintenance schedule and the manufacturer’s data |
Commissioning, annual checks and the load test
Commission the day tank as a system. Check support, slope, vent, overflow, drain, labels, bonding and access before filling. Confirm supply falls to the engine and return falls to the tank, with no high point added by a support or cable tray. Compare the level indication with a physical measurement; a gauge that reads correctly at half level but wrongly at the alarm point is worse than none.
Run the dynamic test with the engine at load. At commissioning, use a load bank to take the set through 50 % to 100 % of rating and record inlet pressure, return backpressure, transfer pump flow and level stability at each step. Repeat once a year at 50 % to 100 % of rating. A set that only runs at 10 % to 20 % of rating does not prove the fuel system at full flow, and that band carries risks including wet stacking and poor combustion.
The 40 °C reference ambient matters to the fuel system as well as the engine. Fuel near a hot enclosure can expand, and a hot return can raise tank temperature. Confirm that the vent handles thermal breathing, the tank is not in a trapped hot corner, and the return does not run beside exhaust or steam. A hot day can raise the level above the fill point, so the high-level alarm and overflow must remain effective.
On a data center site, do not confuse the day tank with the autonomy figure. The UPS covers the seconds between mains loss and generator load, not an hours-long outage. The generator and its fuel system carry the site after that, and the main tank provides long-duration storage. A 1000 kVA set at about 200 litres an hour needs about 4800 litres for 24 hours, while the day tank may hold only a few hours. The PUE 1.4 example confirms that the generator is sized on total site load, not only IT load. Keep the as-built drawing with the test records.
Send the day tank layout and the return-line drawing
Tell us the engine inlet window, the day tank elevation, the transfer pump flow and the return route. The reply sets out the head budget, the return-line checks and the commissioning records to prepare before the next load test, in writing.
How is day tank head pressure measured?
Measure at the engine fuel inlet with the tank at its lowest normal level and the engine at full load. Compare it with the engine manufacturer’s inlet window, then repeat at high level to confirm the maximum is not exceeded.
Can the engine return line go back to the main tank?
It can, but the return must still meet the engine manufacturer’s backpressure limit and must not create a long, air-trapping route. Returning to the day tank keeps the hot return and air separation local. The choice is set by the project layout and equipment data.
How do I size the return line?
Use maximum return flow at full load, allowable return backpressure and the highest expected fuel temperature. Check the as-built route for high points, reductions and closed valves. Burn rate is not the sizing flow.
What level alarms should a day tank have?
A typical sequence has low-low, low, high and high-high levels, with high-high independent of normal control. Setpoints and actions are set by the manufacturer’s data and project specification. Test every input by simulation.
How long should a day tank last?
Autonomy is a project decision. Calculate usable volume from consumption at the expected load and required hours, then confirm it is available between the low-level alarm and high-level stop. A 1000 kVA set at about 200 litres an hour uses about 1600 litres in eight hours; the main tank normally provides a 24-hour reserve.
What should be checked at the annual load test?
Run at 50 % to 100 % of rating once a year and record inlet pressure at low tank level, return backpressure, transfer pump flow and level stability. Confirm alarms and overflow, and inspect the strainer, return line and vent. Check the 10 % to 20 % light-load band for wet stacking.
KVA Grid sales engineering desk. The figures are published elsewhere on this site: the annual load test at 50 % to 100 % and the 10 % to 20 % light-load band from the maintenance schedule; 0.24 to 0.29 litres per delivered kWh, and 101, 80 and 60 litres an hour for a 500 kVA set at full, 75 % and 50 % load, from fuel consumption; the 1000 kVA example at about 200 litres an hour and 4800 litres for 24 hours, and PUE 1.4 from data center backup power; the 40 °C reference from hot and humid climates; tank arrangements from generator fuel tanks and autonomy; vent and overfill protection from fuel tank vent sizing and overfill protection; fuel quality from fuel polishing; and commissioning records from the commissioning checklist. Day tank autonomy, inlet head limits, return-flow limits and level setpoints are set by the manufacturer’s data and the project specification. Reviewed 6 November 2026.
